Salty Matters

The Blog is written by me, John Warren. Once every three or four weeks or so I will post an article or two on an evaporite topic that has piqued my interest. On the Saltwork Publications webpage (under "the Works") there is a growing library of pdfs and epubs based on these blogs. These articles on the website have much higher resolution extractable graphics in than in the blog. There is also a link to this set of pdfs and epubs on the home page (

Brine evolution and origins of potash - primary or secondary. Ancient potash ores: Part 3 of 3

John Warren - Monday, December 31, 2018


In the previous two articles in this series on potash exploitation, we looked at the production of either MOP or SOP from anthropogenic brine pans in modern saline lake settings. Crystals of interest formed in solar evaporation pans and came out of solution as: 1) Rafts at the air-brine interface, 2) Bottom nucleates or, 3) Syndepositional cements precipitated within a few centimetres of the depositional surface. In most cases, periods of more intense precipitation tended to occur during times of brine cooling, either diurnally or seasonally (sylvite, carnallite and halite are prograde salts). All anthropogenic saline pan deposits examples can be considered as primary precipitates with chemistries tied to surface or very nearsurface brine chemistry.

In contrast, this article discusses ancient potash deposits where the chemistries and ore textures are responding to ongoing alteration processes in the diagenetic realm. Unlike the modern brine pans where brines chemistries and harvested mineralogies are controllable, at least in part, these ancient deposits show ore purities and distributions related to ongoing natural-process overprints.

Table 1 lists some modern and ancient potash deposits and prospects by dividing them into Neogene and Pre-Neogene deposits (listing is extracted and compiled from SaltWork® database Version 1.7). The Neogene deposits are associated with a time of MgSO4-enriched seawaters while a majority of the Pre-Neogene deposits straddle times of MgSO4 enrichment and depletion in the ocean waters.

Incongruent dissolution in burial

Many primary evaporite salts dissolve congruently in the diagenetic realm; i.e., the composition of the solid and the dissolved solute stoichiometrically match, and the dissolving salt goes entirely into solution (Figure 1a). This situation describes the typical subsurface dissolution of anhydrous evaporite salts such as halite or sylvite. However, some evaporite salts, typically hydrated salts, such as gypsum or carnallite, dissolve incongruently in the diagenetic realm, whereby the composition of the solute in solution does not match that of the solid (Figure 1b). This solubilisation or mineralogical alteration is defined by the transformation of the "primary solid" into a secondary solid phase, typically an anhydrous salt, and the loss of water formerly held in the lattice structure. The resulting solution generally carries ions away in solution.

More than a century ago, van't Hoff (1912) suggested that much subsurface sylvite is the result of incongruent solution of carnallite yielding sylvite and a Mg-rich solution. According to Braitsch (1971, p. 120), the incongruent alteration (dissolution) of carnallite is perhaps the most crucial process in the alteration of subsurface potash salts and the formation of diagenetic (secondary) sylvite.

Widespread burial-driven incongruent evaporite reactions in the diagenetic realm include the burial transition of gypsum to anhydrite (reaction 1)

CaSO4.2H2O --> CaSO4 + 2 H2O ... (1)

and the in-situ conversion of carnallite to sylvite via the loss of magnesium chloride in solution (reaction 2)

KMgCl3.6H2O --> KCl + Mg++ + 2Cl- + 6H2O ...(2)

Typically, a new solid mineral remains, and the related complex solubility equilibrium creates a saline pore water that may, in turn, drive further alteration or dissolution as it leaves the reaction site (Warren, Chapters 2 and 8). Specifically for ancient potash, reaction 2 generates magnesium and chloride in solution and has been used to explain why diagenetic bischofite and dolomite can be found in proximity to newly formed subsurface sylvite. Bischofite is a highly soluble salt and so is metastable in many subsurface settings where incongruent dissolution is deemed to have occurred, including bischofite thermal pool deposits in the Dallol sump in the Danakhil of Ethiopia (Salty Matters, May 1, 2015). In many hydrologically active systems, solid-state bischofite is flushed by ongoing brine crossflow and so help drive the formation of various burial dolomites. Only at high concentrations of MgCl2 can carnallite dissolve without decomposition.

Laboratory determinations

In the lab, the decomposition of carnallite in an undersaturated aqueous solution is a well-documented example of incongruent dissolution (Emons and Voigt, 1981; Xia et al., 1993; Hong et al., 1994; Liu et al., 2007; Cheng et al., 2015, 2016). When undersaturated water comes into contact with carnallite, the rhombic carnallite crystals dissolve and, because of the common ion effect, small cubic KCl crystals form in the vicinity of the dissolving carnallite. As time passes, the KCl crystals grow into larger sparry subhedral forms and the carnallite disappears.

Carnallite’s crystal structure is built of Mg(H2O)6 octahedra, with the K+ ions are situated in the holes of chloride ion packing meshworks, with a structural configuration similar to perovskite lattice types (Voigt, 2015). Potassium in the carnallite lattice can be substituted by other large single-valence ions like NH4+, Rb+, Cs+ or Li(H2O)+, (H3O)+ and Cl- by Br- and I-. These substitutions change the lattice symmetry from orthorhombic in the original carnallite to monoclinic.

When interpreting the genesis of ancient potash deposits and solutions, the elemental segregation in the lattice means trace element contents of bromide, rubidium and caesium in primary carnallite versus sylvite daughter crystals from incongruent dissolution can provide valuable information. For example, in a study by Wardlaw, (1968), a trace element model was developed for sylvite derived from carnallite that gave for Br and Rb concentration ranges of 0.10–0.90 mg/g and 0.01–0.18 mg/g, respectively. In a later study of sylvite derived by fresh-water leaching of magnesium chloride under isothermal conditions at 25 °C. Cheng et al. (2016), defined a model whereby primary sylvites precipitated from MgSO4-deficient sea water, gave Br and Rb concentration ranges of 2.89–3.54 mg/g and 0.017–0.02 mg/g, respectively (no evaporation occurred at saturation with KCl). In general, they concluded sylvite derived incongruently from carnallite would contain less Br and more Rb than primary sylvite (Figure 2; Cheng et al., 2016).

Subsurface examples

The burial-driven mechanism widely cited to explain the incongruent formation of sylvite from carnallite is illustrated in Figure 3 (Koehler et al., 1990). Carnallite precipitating from evaporating seawater at time 1 forms from a solution at 30°C and atmospheric (1 bar) pressure, and so plots as point A, which lies within the carnallite stability field (that is, it sits above the dashed light brown line). With subsequent burial, the pressure increases so that the line defining carnallite-sylvite boundary (solid dark brown line) moves to higher values of K. By time 2, when the pressure is at 1 Kbar (corresponds to a lithostatic load equivalent to 2-3 km depth), the buried carnallite is thermodynamically unstable and so is converting to sylvite + solution (as the plot field now lies in the sylvite + solution field (Figure 3). If equilibrium is maintained the carnallite reacts incongruently to form further sylvite and MgCl2-solution. Thus, provided the temperature does not rise substantially, increasing pressure as a result of burial will favour the breakdown of carnallite to sylvite. However, as burial proceeds, the temperature may become high enough to favour once again the formation of carnallite from sylvite + solution (that is the solution plot point from A moves toward the right-hand side of the figure and back into the carnallite stability field).

Sylvite, interpreted to have formed from incongruent dissolution of primary carnallite, is reported from the Late Permian Zechstein Formation of Germany (Borchert and Muir, 1964), Late Permian Salado Formation of New Mexico (Adams, 1970), Early Mississippian Windsor Group of Nova Scotia (Evans, 1970), Early Cretaceous Muribeca Formation of Brazil and its equivalents in the Gabon Basin, West Africa (Wardlaw, 1972a, b; Wardlaw and Nicholls, 1972; Szatmari et al., 1979; de Ruiter, 1979), Late Cretaceous of the Maha Sarakham Formation, Khorat Plateau, Thailand and Laos (Hite and Japakasetr, 1979), Pleistocene Houston Formation, Danakil Depression, Ethiopia (Holwerda and Hutchinson, 1968), and Middle Devonian Prairie Formation of western Canada (Schwerdtner, 1964; Wardlaw, 1968) (See Table 1).

This well-documented literature base supports a long-held notion that there is a problem with sylvite as a primary (first precipitate) marine bittern salt, especially if the mother seawater had ionic proportions similar to those present in modern seawater (see Lowenstein and Spencer, 1990 for an excellent, if 30-year-old, review). We know from numerous evaporation experiments, that sylvite does not crystallise during the evaporation of modern seawater at 25°C, except under metastable equilibrium conditions (Braitsch, 1971; Valyashko, 1972; Hardie, 1984). The sequence of bitterns crystallising from modern seawater bitterns was illustrated in the previous Salty Matters article in this series (see Figure 1 in October 31 2018).

Across the literature documenting sylvite-carnallite associations in ancient evaporites, the dilemma of primary versus secondary sylvite is generally solved in one of three ways. Historically, many workers interpreted widespread sylvite as a diagenetic mineral formed by the incongruent dissolution of carnallite (Explanation 1). Then there is the interpretation that some sylvite beds, perhaps associated with tachyhydrite, were precipitated in the evaporite bittern part of a basin hydrology that was fed by CaCl2-rich basinal hydrothermal waters (Explanation 2: see Hardie, 1990 for a good discussion    of this mechanism). Then there is the third, and increasingly popular explanation of primary or syndepositional sylvite at particular times in the chemical evolution of the world oceans (MgSO4-depleted oceans).

Changes in the relative proportions of magnesium, sulphur and calcium in the world’s oceans are well supported by brine inclusion chemistry of co-associated chevron halite (Figure 4). Clearly, there are vast swathes of times in the earth’s past when the chemistry of seawater changed so that MgSO4 levels were lower than today and it was possible that sylvite was a primary marine bittern precipitate (see Lowenstein et al., 2014 for an excellent summary).

In my opinion, there is good evidence that all three explanations are valid within their relevant geological contexts but, if used exclusively to explain the presence of ancient sylvite, the argument becomes somewhat dogmatic. I would say that that, owing to its high solubility, the various textures and mineralogical associations of carnallite/sylvite and sulphate bitterns found in ancient potash ore beds reflect various and evolving origins. Ambient textures and mineralogies are dependent on how many times and how pervasively in a potash sequence’s geological burial history an evolving and reactive pore brine chemistry came into contact with parts or all of the extent of highly reactive potash beds (Warren, 2000; 2010; 2016).

In my experience, very few ancient examples of economic potash show layered textures indicating primary precipitation on a brine lake floor, instead, most ancient sylvite ores show evidence of at least one episode of alteration. That is, various forms and textures in potash may dissolve, recrystallise and backreact with each other from the time a potash salt is first precipitated until it is extracted. The observed textural and mineralogical evolution of a potash ore association depends on how open was the hydrology of the potash system at various stages during its burial evolution. The alteration can occur syndepositionally, in brine reflux, or later during flushing by compactional or thermobaric subsurface waters or during re-equilibration tied to uplift and telogenesis. Tectonism (extensional and compactional) during the various stages of a basin’s burial evolution acts as a bellows driving fluid flow within a basin, so forcing and speeding up the focused circulation of potash-altering waters.


A similar, but somewhat less intense, textural evolution tied to incongruent alteration is seen in the burial history of other variably hydrated evaporite salts. For example, CaSO4 can flip-flop from gypsum to anhydrite and back again depending on temperature, pore fluid salinity and the state of uplift/burial. Likewise, with the more complicated double salt polyhalite, there are mineralogical changes related to whether it formed in a MgSO4 enriched or depleted world ocean and the associated chemistry of the syndepositional reflux brines across extensive evaporite platforms (for a more detailed discussion of polyhalite see Salty Matters, July 31, 2018). Kainite-kieserite-carnallite also show evidence of ongoing incongruent interactions. This means that, as in gypsum/anhydrite/polyhalite or kain ite/kieserite sequences, there will be primary and secondary forms of both carnallite and sylvite that can alternate during deposition, during burial and any deep meteoric flushing and then again with uplift. In Quaternary brine factories these same incongruent chemical relationships are what facilitate the production of MOP (sylvite) from a carnallitite feed or SOP from kainite/kieserite/schoenite feed (see articles 1 and 2 in this series).


To document the three end-members of ancient sylvite-carnallite decomposition/precipitation we will look at three examples; 1) Oligocene potash in the Mulhouse Basin where primary sylvite textures are commonplace, 2) Devonian potash ores in western Canada, where multiple secondary stages of alteration are seen, and 3) Igneous-dyke associated sylvite in east Germany where thermally-driven volatisation (incongruent melting) forms sylvite from dehydrated carnallite.

Oligocene Potash, Mulhouse Basin France

Moving backwards into deep time, this 34 Ma deposit contains some of the first indications of well preserved primary marine-fed sylvinite (MOP) textures exemplified by laterally-continuous mm-scale alternations of potash and halite layers and lamina (Figure 5a-c). Interestingly, all solid-state potash deposits laid down in the post-Oligocene period contain increased proportions of MgSO4 salts, making them much more difficult to economically mine and process (see Table 1 and Salty Matters, May 12, 2015)

From 1904 until 2002, potash was conventionally mined in France from the Mulhouse Basin (near Alsace, France). With an area of 400 km2, the Mulhouse Basin is the southernmost of a number of Lower Oligocene evaporite basins that occupied the upper Rhine Graben, which at that time was a narrow adiabatic-arid rift valley (Figure 6a). The graben was a consequence of the collision between European and African plates during the Paleogene. It is part of a larger intracontinental rift system across Western Europe that extended from the North Sea to the Mediterranean Sea, stretching some 300 km from Frankfurt (Germany) in the north, to Basel (Switzerland) in the south, with an average width of 35 km (Cendon et al., 2008). The southern extent of the graben is limited by a system of faults that place Hercynian massifs and Triassic materials into contact with the Paleogene filling. Across the north, a complex system of structures (including salt diapirs) put the basin edges in contact with Triassic, Jurassic and Permian materials. In the region of the evaporite basins, the Paleogene fill of the graben lies directly on the Jurassic basement. The sedimentary filling of this rift sequence is asymmetrical with the deeper parts located at the southwestern and northeastern sides of the Graben (Rouchy, 1997).

Palaeogeographical reconstructions place the potential marine seaway seepage feed to the north or perhaps also southeast of the Mulhouse Basin, while marginal continental conglomerates tend to preclude any contemporaneous hydrographic connection with Oligocene ocean water (Blanc-Valleron, 1991; Hinsken et al., 2007; Cendon et al., 2008). At the time of its hydrographic isolation, some 34 Ma, the basin was located 40° north of the equator. Total fill of Oligocene lacustrine/marine-fed sediments in the graben is some 1,700m thick. The saline stage is dominated by anhydrite, halite and mudstone. The main saline sequence is underlain by non-evaporitic Eocene continental mudstones, with lacustrine fossils and local anhydrite beds. Evaporite bed continuity in the northern part of the basin is disturbed by (Permian-salt cored) diapiric and or erosional/fault movement. Consequently, these northern basins are not considered suitable for conventional potash mining (Figure 6a).

The Paleogene fill of the basin is divided into 6 units; a pre-evaporitic series, Lower Salt Group (LSG), Middle Salt Group (MSG), an Upper Salt Group (USG - with potash), Grey Marls Fm., and the Niederroedern Fm (Figure 7; Cendon et al., 2008). The LSG and lower section of the MSG are interpreted as lacustrine in origin, based on the limited palaeontologic and geochemical data. However, based on the presence of Cenozoic marine nannoplankton, shallow water benthic foraminifera, and well-diversified dinocyst assemblages in the fossiliferous zone below Salt IV, Blanc-Valleron (1991) favours a marine influence near the top of the MSG, while recognising the ambiguity of marine proportions with brackish faunas. Many marine-seepage fed brine systems have salinities that allow halotolerant species to flourish in marine-fed basins with no ongoing marine hydrographic connection (Warren, 2011). According to Blanc-Valleron and Schuler (1997), the region experienced a Mediterranean climate with long dry seasons during Salt IV member deposition.

In detail, the Salt IV member is made up of some 210 m of evaporitic sequence, with two relatively thin potash levels (Ci and Cs). The stratigraphy associated with this potash zone is, from base to top (Figure 7):

S2 Unit: 11.5 m thick with distinct layers of organic-rich marls, often dolomitic, with dispersed anhydrite layers.

S1 Unit: 19 m thick, evenly-bedded and made up of alternating metre-scale milky (inclusion-rich) halite layers, with much thinner marls and anhydrite layers. Marls show a sub-millimetric lamination formed by micritic carbonate laminae alternating with clay, quartz, and organic matter-rich laminae. Hofmann et al. (1993a, b) interpreted these couplets as reflecting seasonal variations. Anhydrite occasionally displays remnant swallowtail ghost textures, which suggest that at least part of the anhydrite first precipitated as subaqueous gypsum. Halite shows an abundance of growth-aligned primary chevron textures, along with fluid-inclusion banding suggesting halite was subaqueous and deposited beneath shallow brine sheets (Lowenstein and Spencer, 1990).

S Unit: Is 3.7 m thick and consists of thin marl layers and anhydrite, similar to the S2 Unit, with a few thin millimetric layers of halite.

Mi Unit: With a thickness of 6 m, it is mostly halite with similar characteristics to the S1 Unit. Sylvite was detected in one sample, but its presence is probably related to the evolution of interstitial brines (Cendon et al., 2008).

Ci Unit (“Couche inférieure”): Is formed by 4 m of alternating marls/anhydrite, halite, and sylvite beds (Figure 7).

The Ti unit consists of alternating beds of halite, marl and anhydrite. The top of the interval is the T unit, which is similar to the S unit and consists of alternating beds of marl and anhydrite. Above this is the Ms or upper Marl, near identical to the lower marl Mi. The Mi is overlain by the upper potash bed (Cs), a thinner, but texturally equivalent, bed compared to the sylvinitic Ci unit.

Thus, the Oligocene halite section includes two thin, but mined, potash zones: the Couche inferieure (Ci; 3.9m thick), and Couche superieure (Cs; 1.6m thick), both occur within Salt IV of the Upper Salt group (Figures 5, 7).

Both potash beds are made up of stacked, thin, parallel-sided cm-dm-thick beds (averaging 8 cm thickness), which are in turn constructed of couplets composed of grey-coloured halite overlain by red-coloured sylvite (Figure 5b). Each couplet has a sharp base that separates the basal halite from the sylvite cap of the underlying bed. In some cases, the separation is also marked by bituminous partings. The bottom-most halite in each dm-thick bed consists of halite aggregates with cumulate textures that pass upward into large, but delicate, primary chevrons and cornets. Clusters of this chevron halite swell upward to create a cm-scale hummocky boundary with the overlying sylvite (Figure 5c; Lowenstein and Spencer, 1990).

The sylvite member of a sylvinite couplet consists of granular aggregates of small transparent halite cubes and rounded grains of red sylvite (with some euhedral sylvite hoppers) infilling the swales in the underlying hummocky halite (Figure 5b,c). The sylvite layer is usually thick enough to bury the highest protuberances of the halite, so that the top of each sylvite layer, and the top of the couplet, is flat. Dissolution pipes and intercrystalline cavities are noticeably absent, although some chevrons show rounded coigns. Intercalated marker beds, formed during times of brine pool freshening, are composed of a finely laminated bituminous shale, with dolomite and anhydrite.

The sylvite-halite couplets record combinations of unaltered settle-out and bottom-nucleated growth features, indicating primary chemical sediment accumulating in shallow perennial brine pools (Lowenstein and Spencer, 1990). Based on the crystal size, the close association of halites with sylvite layers, their lateral continuity and the manner in which sylvite mantles overlie chevron halites, the sylvites are interpreted as primary precipitates. Sylvite first formed at the air-brine surface or within the uppermost brine mass and then sank to the bottom to form well-sorted accumulations. As sylvite is a prograde salt it, like halite, probably grew during times of cooling of the brine mass (Figure 8a). These times of cooling could have been diurnal (day/night) or weather-front induced changes in the above-brine air temperatures. Similar cumulate sylvite deposits form as ephemeral bottom accumulations on the floor of modern Lake Dabuxum in China during its more saline phases.

The subsequent mosaic textural overprint seen in many of the Mulhouse sylvite layers was probably produced by postdepositional modification of the crystal boundaries, much in the same way as mosaic halite is formed by recrystallisation of raft and cumulate halite during shallow burial. Temperature-based inclusion studies in both the sylvite and the halites average 63°C, suggesting solar heating of surface brines as precipitation took place (Figure 8b; Lowenstein and Spencer, 1990). Similar high at-surface brine temperatures are not unusual in many modern brine pools, especially those subject to periodic density stratification and heliothermometry (Warren 2016; Chapter 2).

Mineralogically, potash evaporites in the Mulhouse Basin in the Rhine Graben (also known as the Alsatian (Alsace) or Wittelsheim Potash district) contain sylvite with subordinate carnallite, but lack the abundant MgSO4 salts characteristic of the evaporation of modern seawater. The Rhine graben formed during the Oligocene, via crustal extension, related to mantle upwelling. It was, and is, a continental graben typified by high geothermal gradients along its rift axis. In depositional setting, it is not dissimilar to pree-120,000-year potash fill stage in the Quaternary Danakil Basin or the Dead Sea during deposition of potash salts in the Pliocene Sedom Fm. The role of a high-temperature geothermal inflow in defining the CaCl2 nature of the potash-precipitating brines, versus a derivation from a MgSO4-depleted marine feed, is considered significant in the Rhine Graben deposits, but is poorly understood and still not resolved (Hardie, 1990; Cendón et al., 2008). World ocean chemistry in the Oligocene is on a shoulder between the MgSO4-depleted CaCl2-rich oceans of the Cretaceous and the MgSO4-enriched oceans of the Neogene (Figure 4).

Cendón et al. (2008) conclude brine reaction processes were the most important factors controlling the major-ion (Mg, Ca, Na, K, SO4, and Cl) evolution of Mulhouse brines (Figure 9a-d). A combined analysis of fluid inclusions in primary textures by Cryo-SEM-EDS with sulphate- d34S, d18O and 87Sr/86Sr isotope ratios revealed likely hydrothermal inputs and recycling of Permian evaporites, particularly during the more advanced stages of evaporation that laid down the Salt IV member. Bromine levels imply an increasingly concentrated brine at that time (Figure 9a). The lower part of the Salt IV (S2 and S1) likely evolved from an initial marine input (Figure 9b-d).

Throughout, the basin was disconnected from direct marine hydrographic connection and was one of a series of sub-basins formed in an active rift setting, where tectonic variations influenced sub-basin interconnections and chemical signatures of input waters. Sulphate-d34S shows Oligocene marine-like signatures at the base of the Salt IV member (Figure 9c, d). However, enriched sulphate-d18O reveals the importance of synchronous re-oxidation processes.

As evaporation progressed, other non-marine or marine-modified inputs from neighbouring basins became more important. This is demonstrated by increases in K concentrations in brine inclusions and Br in halite, sulphate isotopes trends, and 87Sr/86Sr ratios (Figure 9b, c). The recycling (dissolution) of previously precipitated evaporites of Permian age was increasingly important with ongoing evaporation. In combination, this chemistry supports the notion of a connection of the Mulhouse Basin with basins situated north of Mulhouse. The brine evolution eventually reached sylvite precipitation. Hence, the chemical signature of the resulting brines is not 100% compatible with global seawater chemistry changes. Instead, the potash phase is tied to a hybrid inflow, with significant but decreasing marine input.

There was likely an initial marine source, but this occurred within a series of rift-valley basin depressions for which there was no direct hydrographic connection to the open ocean, even at the time the Middle Salt Member (potash-entraining) was first deposited (Cendon et al., 2008). That is, the general hydrological evolution of the primary textured evaporites in the Mulhouse basin sump is better explained as a restricted sub-basin with an initial marine-seepage stage. This gradually changed to ≈ 40% marine source near the beginning of evaporite precipitation, with the rest of hydrological inputs being non-marine. There was a significant contribution of solutes from recycled, in part diapiric, Permian evaporites, likely remobilised by the tectonics driving the formation of the rift valley (Hinsken et al., 2007; Cendon et al., 2008). The general proportion of solutes did not change substantially over the time of evaporite precipitation. However, as the basin restriction increased, the formerly marine inputs changed to continental, diapiric or marine-modified inputs, perhaps fed from neighbouring basins north of Mulhouse basin. As in the Ethiopian Danakhil potash-rift, it is likely brine interactions occurred both during initial and early post-depositional reflux overprinting of the original potash salt beds.

West Canadian potash (Devonian)

The Middle Devonian (Givetian) Prairie Evaporite Formation is a widespread potash-entraining halite sequence deposited in the Elk Point Basin, an early intracratonic phase of the Western Canada Sedimentary Basin (WCSB; Chipley and Kyser, 1989). Today, it is the world’s predominant source of MOP fertiliser (Warren, 2016). The flexure that formed the basin and its subsealevel accommodation space was a distal downwarp to, and driven by, the early stages of the Antler Orogeny (Root, 2001). Texturally and geochemically the potash layers in the basin show the effects of multiple alterations and replacements of its potash minerals, especially interactions between sylvite and carnallite in a variably recrystallised halite host.

Regionally halite constitutes a large portion of the four formations that make up the Devonian Elk Point Group (Figure 10): 1) the Lotsberg (Lower and Upper Lotsberg Salt), 2) the Cold Lake (Cold Lake Salt), 3) the Prairie Evaporite (Whitkow and Leofnard Salt), and 4) the Dawson Bay (Hubbard Evaporite). Today the remnants of the Middle Devonian Prairie Evaporite Formation constitute a bedded unit some 220 metres thick, which lies atop the irregular topography of the platform carbonates of the Winnipegosis Fm. Extensive solutioning of the various salts has given rise to an irregular thickness to the formation and the local absence of salt (Figure 11a).

The Elk Point Group was deposited within what is termed the Middle Devonian “Elk Point Seaway,” a broad intracratonic sag basin extending from North Dakota and northeastern Montana at its southern extent north through southwestern Manitoba, southern and central Saskatchewan, and eastern to northern Alberta (Figure 11a). Its Pacific coast was near the present Alberta-British Columbia border, and the basin was centred at approximately 10°S latitude. To the north and west the basin was bound by a series of tectonic ridges and arches; but, due to subsequent erosion, the true eastern extent is unknown (Mossop and Shetsen, 1994). In northern Alberta, the Prairie Evaporite is correlated with the Muskeg and Presqu’ile formations (Rogers and Pratt, 2017).

Hydrographic isolation of the intracratonic basin from its marine connection resulted in the deposition of a drawndown sequence of basinwide (platform-dominant) evaporites with what is a uniquely high volume of preserved potash salts deposited within a clayey halite host. The potash resource in this basin far exceeds that of any other known potash basin in the world.

Potash geology

Potash deposits mined in Saskatchewan are all found within the upper 60-70 m of the Prairie Evaporite Formation, at depths of more than 400 to 2750 metres beneath the surface of the Saskatchewan Plains. Within the Prairie Evaporite, there are four main potash-bearing members, in ascending stratigraphic order they are: Esterhazy, White Bear, Belle Plaine and Patience Lake members (Figure 11b). Each member is composed of various combinations of halite, sylvite, sylvinite, and carnallitite, with occurrences of sylvite versus carnallite reliably definable using wireline signatures (once the wireline is calibrated to core or mine control - Figure 12; Fuzesy, 1982).

The Patience Lake Member is the uppermost Prairie Evaporite member and is separated from the Belle Plaine by 3-12 m of barren halite (Holter, 1972). Its thickness ranges from 0-21 m and averages 12 m, its top 7-14 m is made up halite with clay bands and stratiform sylvite. This is the targeted ore unit in conventional mines in the Saskatoon and Lanigan areas and is the solution-mined target, along with the underlying Belle Plaine Member, at the Mosaic Belle Plaine potash facility. The Belle Plaine member is separated from the Esterhazy by the White Bear Marker beds made up of some 15 m of low-grade halite, clay seams and sylvinite. The Belle Plaine Member is more carnallite-prone than the Patience Lake member (Figure 12). It is the ore unit in the conventional mines at Rocanville and Esterhazy (Figure 11b) where its thickness ranges from 0-18 m and averages around 9 m. In total, the Prairie Evaporite Formation does not contain any significant MgSO4 minerals (kieserite, polyhalite etc.) although some members do contain abundant carnallite. This mineralogy indicates precipitation from a Devonian seawater/brine chemistry somewhat different from today’s, with inherently lower relative proportions of sulphate and lower Mg/Ca ratios (Figure 4).

The Prairie Evaporite Fm. is nonhalokinetic throughout the basin, it is more than 200 m thick in the potash mining district in Saskatoon and 140 m thick in the Rocanville area to the southeast (Figure 11a; Yang et al., 2009). The Patience Lake member is the main target for conventional mining near Saskatoon. The Esterhazy potash member rises close to the surface in the southeastern part of Saskatchewan near Rocanville and on into Manitoba. This is a region where the Patience Lake Member is thinner or completely dissolved (Figure 11b). Over the area of mineable interest in the Patience Lake Member, centred on Saskatoon, the ore bed currently slopes downward only slightly in a westerly direction, but deepens more strongly to the south at a rate of 3-9 m/km. Mines near Saskatoon are at depths approaching a kilometre and so are nearing the limits of currently economic shaft mining.

The main shaft for the Colonsay Mine, which took IMC Global Inc. more than five years to complete through a water-saturated sediment column, finally reached the target ore body at a depth of 960 metres. Such depths and a southerly dip to the ore means that the conventional shaft mines near Saskatoon define a narrow WNW-ESE band of conventional mining activity (Figure 11c). To the south potash is recovered from greater depths by solution mining; for example, the Belle Plaine operation leaches potash from the Belle Plaine member at a depth of 1800m.

The Prairie Evaporite typically thins southwards in the basin; although local thickening occurs where carnallite, not sylvite, is the dominant potash mineral (Worsley and Fuzesy, 1979). The Patience Lake member is mined at the Cory, Allan and Lanigan mines, and the Esterhazy Member is mined in the Rocanville area (Figure 11c). Ore mined from the 2.4 m thick Esterhazy Member in eastern Saskatchewan contain minimal amounts of insolubles (≈1%), but considerable quantities of carnallite (typically 1%, but up to 10%) and this reduces the average KCl grade value to an average of 25% K2O. The converse is true for ore mined from the Patience Lake potash member in western Saskatchewan near Saskatoon, where carnallite is uncommon in the Cory and Allan mines. The mined ore thickness is a 2.74-3.35 metre cut off near the top of the 3.66-4.57metre Prairie Lake potash member. Ore grade is 20-26% K2O and inversely related to thickness (Figure 12). The insoluble content is 4-7%, mostly clay and markedly higher than in the Rocanville mines.

A typical sylvinite ore zone in the Patience Lake member can be divided into four to six units, based on potash rock-types and clay seams (Figures 12, 13a; M1-M6 of Boys, 1990). Units are mappable and have been correlated throughout the PCS Cory Mine with varying degrees of success, dependent on partial or complete loss of section from dissolution. Potash deposition appears to have been early and related to short-term brine seaway cooling and syndepositional brine reflux. So the potash layering (M1-M6) is cyclic, expressed in the repetitive distribution of hematite and other insoluble minerals (Figure 13). Desiccation polygons, desiccation cracks, subvertical microkarst pits and chevron halite crystals indicate that the Patience Lake member that encompasses the potash ore was deposited in and just beneath a shallow-brine, salt-pan environment (Figure 13b; Boys, 1990; Lowenstein and Spencer, 1990; Brodlyo and Spencer, 1987; pers. obs).

Clay seams form characteristic thin stratigraphic segregations throughout the potash ore zone(s) of the Prairie Evaporite, as well as disseminated intervals, and constitute about 6% of the ore as mined. For example, the insoluble minerals found in the PCS Cory samples are, in approximate order of decreasing abundance: dolomite, clay [illite, chlorite (including swelling-chlorite/chlorite), and septechlorite, quartz, anhydrite, hematite, and goethite. Clay minerals make up about one-third of the total insolubles: other minor components include: potassium feldspar, hydrocarbons, and sporadic non-diagnostic palynomorphs (Figure 13; Boys, 1990).

In all mines, the clays tend to occur as long continuous seams or marker layers between the potash zones and are mainly composed of detrital chlorite and illite, along withauthigenic septechlorite, montmorillonite and sepiolite (Mossman et al., 1982; Boys, 1990). Of the two chlorite minerals, septechlorite is the more thermally stable. The septechlorite, sepiolite and vermiculite very likely originated as direct products of settle-out, syndepositional dissolution or early diagenesis under hypersaline conditions from a precursor that was initially eolian dust settling to the bottom of a vast brine seaway. The absence of the otherwise ubiquitous septechlorite from Second Red Beds west of the zero-edge of the evaporite basin supports this concept (Figure 9, 10).

Potash Textures

Texturally, at the cm-scale, potash salt beds in the Prairie Evaporite (both carnallitite and sylvinite) lack the lateral continuity seen in primary potash textures in the Oligocene of the Mulhouse Basin (Figure 14). Prairie potash probably first formed as syndepositional secondary precipitates and alteration products at very shallow depths just beneath the sediment surface. These early prograde precipitates were then modified to varying degrees by ongoing fluid flushing in the shallow burial environment. The cyclic depositional distribution of disseminated insolubles as the clay marker beds was possibly due to a combination of source proximity, periodic enrichment during times of brine freshening and the strengthening of the winds blowing detritals out over the brine seaway. Possible intra-potash disconformities, created by dissolution of overlying potash-bearing salt beds, are indicated by an abundance of residual hematite in clay seams with some cutting subvertically into the potash bed. Except in, and near, dissolution levels and collapse features, the subsequent redistribution of insolubles, other than iron oxides, is not significant.

In general, halite-sylvite (sylvinite) rocks in the Prairie Evaporite ore zones generally show two end member textures; 1) the most common is a recrystallised polygonal mosaic texture with individual crystals ranging from millimetres to centimetres and sylvite grain boundaries outlined by concentrations of blood-red halite (Figure 14a). 2) The other end member texture is a framework of euhedral and subhedral halite cubes enclosed by anhedral crystals of sylvite (Figure 14b). This is very similar to ore textures in the Salado Formation of New Mexico interpreted as early passive precipitates in karstic voids.

Petrographically, the halite-carnallite (carnallitite) rocks display three distinct textures. Most halite-carnallite rocks contain isolated centimetre-sized cube mosaics of halite enclosed by poikilitic carnallite crystals (Figure 14c); 1) Individual halite cubes are typically clear, with occasional cloudy crystal cores that retain patches of syndepositional growth textures (Lowenstein and Spencer, 1990). 2) The second texture is coarsely crystalline halite-carnallite with equigranular, polygonal mosaic textures. In zones where halite overlies bedded anhydrite, most of the halite is clear with only the occasional crystal showing fluid inclusion banding.

Bedded halite away from the ore zones generally retains a higher proportion of primary depositional textures typical of halite precipitation in shallow ephemeral saline pans (Figure 14d; Brodylo and Spencer, 1987). Crystalline growth fabrics, mainly remnants of vertically-elongate halite chevrons, are found in 50-90% of the halite from many intervals in the Prairie Evaporite. Many of the chevrons are truncated by irregular patches of clear halite that formed as early diagenetic cements in syndepositional karst.

In contrast, the halite hosting the potash ore layers lacks well-defined primary textures but is dominated by intergrown mosaics. From the regional petrology and the lower than expected Br levels in halite in the Prairie Evaporite Formation, Schwerdtner (1964), Wardlaw and Watson (1966) and Wardlaw (1968) postulated a series of recrystallisation events forming sylvite after carnallite as a result of periodic flushing by hypersaline solutions. This origin as a secondary precipitate (via incongruent dissolution) is supported by observations of intergrowth and overgrowth textures (McIntosh and Wardlaw, 1968), collapse and dissolution features at various scales and timings (Gendzwill, 1978; Warren 2017), radiometric ages (Baadsgaard, 1987) and palaeomagnetic orientations of the diagenetic hematite linings associated with the emplacement of the potash (Koehler, 1997; Koehler et al., 1997).

Dating of clear halite crystals in void fills within the ore levels shows that some of the exceptionally coarse and pure secondary halites forming pods in the mined potash horizons likely precipitated during early burial, while other sparry halite void fills formed as late as Pliocene-Pleistocene (Baadsgard, 1987). Even today, alteration and remobilisation of the sylvite and carnallite and the local precipitation of bischofite are ongoing processes, related to the encroachment of the contemporary dissolution edge or the ongoing stoping of chimneys fed by deep artesian circulation (pers obs.).

Fluid inclusion studies support the notion of primary textures (low formation temperatures in chevron halite in the Prairie evaporite and an associated thermal separation of non-sylvite and sylvite associated halite (Figure 15; Chipley et al., 1990). Most fluid inclusions found in primary, fluid inclusion-banded halite associated with the Prairie potash salts contain sylvite daughter crystals at room temperature or nucleate them on cooling (e.g. halite at 915 and 945 m depth in the Winsal Osler well; Lowenstein and Spencer, 1990). In contrast, no sylvite daughter crystals have been observed in fluid inclusions outlining primary growth textures from chevron halites away from the potash deposits.

The data illustrated as Figure 15 clearly show that inclusion temperatures in primary halite chevrons are cooler than those in halites collected in intervals nearer the potash levels. Sylvite daughter crystal dissolution temperatures from fluid inclusions in the cloudy centres of halite crystals associated with potash salts are generally warmer (Brodlyo and Spencer, 1987; Lowenstein and Spencer, 1990). Sylvite and carnallite daughter crystal dissolution temperatures from fluid inclusions in fluid inclusion banded halite from bedded halite-carnallite are the hottest. This mineralogically-related temperature schism establishes that potash salts occur in stratigraphic intervals in the halite where syndepositional surface brines were warmer. In the 50° - 70°C temperature range there could be overlap with heliothermal brine lake waters. Even so, these warmer potash temperatures imply parent brines would likely be moving via a shallow reflux drive and are not the result of primary bottom nucleation (in contrast to primary sylvite in the Mulhouse Basin). Whether the initial Prairie reflux potash precipitate was sylvite or carnallite is open to interpretation (Lowenstein and Hardie, 1990).

Fluid evolution from mineral and isotope chemistry

Analysis of subsurface waters from various Canadian potash mines and collapse anomalies in the Prairie Evaporite suggest that, after initial potash precipitation, a series of recrystallising fluids accessed the evaporite levels at multiple times throughout the burial history of the Prairie Formation (Chipley, 1995; Koehler, 1997; Koehler et al., 1997). Likewise, the isotope systematics and K-Ar ages of sylvite in both halite and sylvite layers indicate that the Prairie Evaporite was variably recrystallised during fluid overprint events (Table 2; Figure 16). These event ages are all younger than original deposition (≈390Ma) and likely correspond to ages of various tectonic events that influenced subsurface hydrology along the western margin of North America.

Chemical compositions of inclusion fluids in the Prairie Evaporite, as determined by their thermometric properties, reveal at least two distinct waters played a role in potash formation: a Na-K-Mg-Ca-Cl brine, variably saturated with respect to sylvite and carnallite; and a Na-K-Cl brine (Horita et al., 1996). That is, contemporary inclusion water chemistry is a result in part of ongoing fluid-rock interaction. The ionic proportions in some halite samples are not the result of simple evaporation of seawater to the sylvite bittern stage (Figure 17a; Horita et al., 1996). There is a clear separation of values from chevron halites in samples from the Lanigan and Bredenbury (K-2 area) mines, which plot closer to the concentration trend seen in halite from modern seawater and values from clear or sparry halite. The latter encompass much lower K and higher Br related to fractionation tied to recrystallisation. Likewise, the influence of ongoing halite and potash salt dissolution is evident in the chemistry of shaft and mine waters with mine level waters showing elevated Mg and K values, (Figure 17b; Wittrup and Kyser, 1990; Chipley, 1995). What is more the mine waters of today show  substantial overlap with waters collected more than thirty years ago (Jensen et al., 2006)

This notion of ongoing fluid-rock interaction controlling the chemistry of mine waters is supported by dD and d18O values of inclusion fluids in both halite and sylvite, which range from -146 to 0‰ and from -17.6 to -3.0‰, respectively (Figure 18). Most of the various preserved isotope values are different from those of evaporated seawater, which should have dD and d18O values near 0‰.

Furthermore, the dD and d18O values of inclusion fluids are probably not the result of precipitation of the evaporite minerals from a brine that was a mixture of seawater and meteoric water. The low latitude position of the basin during the Middle Devonian (10-15° from the equator), the required lack of meteoric water to precipitate basinwide evaporites, and the expected dD and d18O values of any meteoric water in such a setting, make this an unlikely explanation. Rather, the dD and d18O values of inclusion fluids in the halites reflect ambient and evolving brine chemistries as the fluids in inclusions in the various growth layers were intermittently trapped during the subsurface evolution of the Prairie Formation in the Western Canada Sedimentary Basin. They also suggest that periodic migration of nonmarine subsurface water was a significant component of the crossflowing basinal brines throughout much of the recrystallisation history (Chipley, 1995).

Prairie carnallite-sylvite alteration over time

Ongoing alteration of carnallite to sylvite and the reverse reaction means a sylvite-carnallite bed must be capable of gaining or losing fluid at the time of alteration. That is, any reacting potash beds must be permeable at the time of the alteration. By definition, there must be fluid egress to drive incongruent alteration of carnallite to sylvite or fluid ingress to drive the alteration of sylvite to carnallite. There can also be situations in the subsurface where the volume of undersaturated fluid crossflow was sufficient to remove (dissolve) significant quantities of the more soluble evaporite salts. Many authors looking at the Prairie evaporite argue that the fluid access events during the alteration of carnallite to sylvite or the reverse, or the complete leaching of the soluble potash salts was driven by various tectonic events (Figure 16). In the early stages of burial alteration (few tens of metres from the landsurface) the same alteration processes can be driven by varying combinations of brine reflux, prograde precipitation and syndepositional karstification, all driven by changes in brine level and climate, which in turn may not be related to tectonism (Warren, 2016; Chapters 2 and 8 for details).

In the potash areas of the Western Canada Sedimentary Basin, the notion of 10-100 km lateral continuity is a commonly stated precept for both sylvinite and carnallitite units across the extent of the Prairie Evaporite. But when the actual distribution and scale of units are mapped based on mined intercepts, there are numerous 10-100 metre-scale discontinuities (anomalies) present indicating fluid ingress or egress (Warren, 2017).

Sometimes ore beds thin and alteration degrades the ore level (Section A-A1-A2), other times these discontinuities can locally enrich sylvite ore grade (B-B1; Figure 19). Discontinuities or salt anomalies are much more widespread in the Prairie evaporite than mentioned in much of the potash literature (Figure 19). Mining for maintenance of ore grade shows that unexpectedly intersecting an anomaly in a sylvite ore zone can have a range of outcomes ranging from the inconsequential to the catastrophic, in part because there is more than one type of salt anomaly or “salt horse" (Warren, 2017).

Figure 20 summarises what are considered the three most common styles of salt anomaly in the sylvite ore beds of the Prairie Evaporite, namely 1) Washouts, 2) Leach anomalies, 3) Collapse anomalies. These ore bed disturbances and their occurrence styles are in part time-related. Washouts are typically early (eogenetic) and defined as... “salt-filled V- or U-shaped structures, which transect the normal bedded sequence and obliterate the stratigraphy” (Figure 20a; Mackintosh and McVittie, 1983, p. 60). They are typically enriched in, or filled by, insoluble materials in their lower one-third and medium-coarse-grained sparry halite in the upper two thirds. Up to several metres across, when traced laterally they typically pass into halite-cemented paleo-sinks and cavern networks (e.g. Figure 20b). Most washouts likely formed penecontemporaneous to the potash beds they transect, that is, they are preserved examples of synkarst, with infilling of the karst void by a slightly later halite cement. They indicate watertable lowering in a potash-rich saline sump. This leaching was followed soon after by a period of higher watertables and brine saturations, when halite cements occluded the washouts and palaeocaverns. Modern examples of this process typify the edges of subcropping and contemporary evaporite beds, as about the recently exposed edges of the modern Dead Sea. As such, “washouts” tend to indicate relatively early interactions of the potash interval with undersaturated waters, they may even be a part of the syndepositional remobilisation hydrology that focused, and locally enriched, potash ore levels.

In a leach anomaly zone, the stratabound sylvinite ore zone has been wholly or partially replaced by barren halite, without significantly disturbing the normal stratigraphic sequence (clay marker beds) which tend to continue across the anomaly (Figure 20b). Some loss of volume or local thinning of the stratigraphy is typical in this type of salt anomaly. Typically saucer-shaped, they have diameters ranging from a few metres up to 400m. Less often, they can be linear features that are up to 20 m wide and 1600m long. Leach zones can form penecontemporaneously due to depressions and back-reactions in the ore beds, or by later low-energy infiltration of Na-saturated, K-undersaturated brines. The latter method of formation is also likely on the margins of collapse zones, creating a hybrid situation typically classified as a leach-collapse anomaly (Mackintosh and McVittie, 1983; McIntosh and Wardlaw, 1968).

Of the three types of salt anomaly illustrated, leach zone processes are the least understood. Historically, when incongruent dissolution was the widely accepted interpretation for loss of unit thickness in the Prairie Evaporite, many leach anomalies were considered metasomatic. Much of the original metasomatic interpretation was based on decades of detailed work in the various salt mines of the German Zechstein Basin. There, in an endemic halokinetic terrane, evaporite textures were considered more akin to metamorphic rocks, and the term metasomatic alteration was commonly used when explaining leach anomalies (Bochert and Muir, 1964, Braitsch, 1971). In the past two decades, general observations of the preservation of primary chevron halite in most bedded evaporites away from the potash layers in the Prairie Evaporite have led to reduced use of notions of widespread metamorphic-like metasomatic or solid-state alteration processes in bedded evaporites. There is just too much preserved primary texture in the bedded salt units adjacent to potash beds to invoke pervasive burial metasomatism of the Prairie Evaporite.

So how do leach anomalies, as illustrated in Figure 20b, occur in nonhalokinetic settings? One possible explanation is given by the depositional textures documented in anomalies in the Navarra Potash Province (Figure 21). There, the underlying and overlying salt stratigraphy is contiguous, while the intervening sylvite passed laterally into a syndepositional anomaly or “salt horse” created by an irregular topography on the salt pan floor prior to the deposition of onlapping primary sylvinite layers (see Warren 2016, 2017 for detailed discussion)

On the other hand, in halokinetic situations (which characterises much Zechstein salt) solid-state alteration via inclusion related migration in flowing salt beds is a well-documented set of texture-altering processes (diffusion metasomatism). Most workers in such halokinetic systems would agree that there must have been an original stratiform potassium segregation present during or soon after deposition related to initial precipitation, fractional dissolution and karst-cooling precipitation. But what is controlling potassium distribution now in the Zechstein salts is a recrystallised and remobilised set of textures, which preserve little or no crystal-scale evidence of primary conditions (Warren, 2016; Chapter 6). The complex layering in such deposits may preserve a broad depositional stratigraphy, but the decimetre to metre scale mineral distributions are indications of complex interactions of folds, overfolds, and disaggregation with local flow thickening. We shall return to this discussion of Zechstein potash textures in the next section dealing with devolatisation of hydrated salts such as carnallite. in zones of local heating

Collapse zones in the Prairie Evaporite are characterized by a loss of recognizable sylvinite ore strata, which is replaced by less saline brecciated, recemented and recrystallized material, with the breccia blocks typically made of the intrasalt or roof lithologies (Figure 20c), so angular fragments of the Second Red beds and dolostones of the Dawson Bay Formation are the most conspicuous components of the collapse features in the Western Canada Sedimentary Basin. When ore dissolution is well developed, all the halite can dissolve, along with the potash salts, and the overlying strata collapse into the cavity (these are classic solution collapse features). Transitional leached zones typically separate the collapsed core from normal bedded potash. Such collapse structures indicate a breach of the ore layers by unsaturated waters, fed either from below or above. For example, in the Western Canada Sedimentary Basin, well-developed collapse structures tend to occur over the edges and top Devonian mud mounds, while in the New Mexico potash zone the collapse zones are related to highs in the underlying Capitan reef trend (Warren, 2017). Leaching fluids may have come from below or above to form collapse structures at any time after initial deposition. When connected to a water source, these are the subsurface features that when intersected can quickly move the mining operation out of the salt into an adjacent aquifer system, a transition that led to flooding in most of the mine-lost operations listed earlier.

Identifying at the mine scale the set of processes that created a salt anomaly in a sylvite bed also has implications in terms of its likely influence on mine stability whatever decision is made on how to deal with it as part of the ongoing mine operation (Warren, 2016, 2017). Syndepositional karst fills and leach anomalies are least likely to be problematic if penetrated during mining, as the aquifer system that formed them is likely no longer active. In contrast, penetration or removal of the region around a salt-depleted collapse breccia may lead to uncontrollable water inflows and ultimately to the loss of the mine.

Unfortunately, in terms of production planning, the features of the periphery of a leach anomaly can be similar if not identical to those in the alteration halo that typically forms about the leached edge a collapse zone. The processes of sylvite recrystallisation that define the edge of collapse anomaly can lead to local enrichment in sylvite levels, making these zones surrounding the collapse core attractive extraction targets (Boys 1990, 1993). Boundaries of any alteration halo about a collapse centre are not concentric, but irregular, making the prediction of a feature’s geometry challenging, if not impossible. The safest course of action is to avoid mining salt anomalies, but longwall techniques make this difficult and so they must be identified and dealt with (see Warren 2017).

Cooking sylvite: Dykes & sills in potash salts


In addition to; 1) primary sylvite and 2) sylvite/carnallite alteration via incongruent transformation in burial, there is a third mode of sylvite formation related to 3) igneous heating driving devolatisation of carnallitite, which can perhaps be considered a form of incongruent melting (Warren, 2016). And so, at a local scale (measured in metres to tens of metres) in potash beds cut by igneous intrusions, there are a number of documented thermally-driven alteration styles and thermal haloes. Most are created by the intrusion of hot doleritic or basaltic dykes and sills into cooler salt masses, or the outflow of extrusive igneous flows over cooler salt beds (Knipping, 1989; Grishina et al, 1992, 1998; Gutsche, 1988; Steinmann et al., 1999; Wall et al., 2010). Hot igneous material interacts with somewhat cooler anhydrous salt masses to create narrow, but distinct, heat and mobile fluid-release envelopes, also reflected in the resulting salt textures. At times, relatively rapid magma emplacement can lead to linear breakout trends outlined by phreatomagmatic explosion craters, as imaged in portions of the North Sea (Wall et al., 2010) and the Danakhil/Dallol potash beds in Ethiopia (Salty Matters, May 1, 2015).

Based on studies of inclusion chemistry and homogenization temperatures in fluid inclusions in bedded halite near intrusives, it seems that the extent of the influence of a dolerite sill or dyke in bedded salt is marked by fluid-inclusion migration, evidenced by the disappearance of chevron structures and consequent formation of clear halite with a different set of higher-temperature inclusions. Such a migration envelope is well documented in bedded Cambrian halites intruded by end-Permian dolerite dykes in the Tunguska region of Siberia (Grishina et al., 1992).

Defining h as the thickness of the dolerite intrusion in these salt beds, and d as the distance of the halite from the edge of the intrusion, then the disappearance of chevrons occurs at greater distances above than below the intrusive sill. For d/h < 0.9 below the intrusion, CaCl2, CaCl2, KCl and nCaCl2, mMgCl2 solids occur in association with water-free and liquid-CO2 inclusions, with H2S, SCO and orthorhombic or glassy S8. For a d/h of 0.2-2 above the intrusion, H2S-bearing liquid-CO2 inclusions are typical, with various amounts of water. Thus, as a rule of thumb, an alteration halo extends up to twice the thickness of the dolerite sill above the sill and almost the thickness of the sill below (Figure 22).

In a series of autoclavation laboratory experiments, Fabricius and Rose-Hampton (1988) found that; 1) at atmospheiric pressure carnallite melts incongruently to sylvite and hydrated MgCl2 at a temperature of 167.5°C. 2) the melting/transformation temperature increase to values in excess of 180°C as the pressure increases (Figure 23).

A similar situation occurs in the dyke-intruded halite levels exposed in the mines of the Werra-Fulda district of Germany (Steinmann et al., 1999; Schofield, et al., 2014). There the Herfa-Neurode potash mine is located in the Werra-Fulda Basin in the Hessian district of central Germany (Figure 24a). The targeted ore levels consist of the carnallite-rich Kaliflöz Hessen (K1H) and Kaliflöz Thüringen (K1Th) intervals, which form part of the Zechstein 1 (Z1) bedded Werra salt succession (Warren, 2016). In the mine the K1H and K1Th units range in thickness from 2 m to 10 m, are generally subhorizontal and occur at a depth of 650–710 m below the present-day surface.

In the later Tertiary, basaltic melts intruded these Zechstein evaporites as numerous sub-vertical dykes, but only a few dykes attained the Miocene landsurface. Basaltic melt production was related to regional volcanic activity some 10 to 25 Ma. Basalts exposed in the mine walls, where it cuts non-hydrous units of halite or anhydrite, are typically subvertical dykes, rather than subhorizontal sills. The basalts are phonolitic tephrites, limburgites, basanites and olivine nephelinites. Dyke margins are usually vitrified, forming a microlitic limburgite glass along dyke edges in contact with halite (Figure 24b; Knipping, 1989). At the contact on the evaporite side of the glassy rim, there is a cm-wide carapace of high-temperature salts (mostly anhydrite and ferroan carbonates). Further out, the effect of the high-temperature envelope is denoted by transitions to clear halite, with higher temperature fluid inclusions (Knipping 1989). All of this metre-scale alteration is an anhydrous alteration halo, the halite did not melt (melting temperature of 804°C), rather than migrating, the fluid driving recrystallisation was mostly from entrained brine/gas inclusions. The dolerite/basalt interior of the basaltic dyke is likewise altered and salt soaked, with clear, largely inclusion-free halite typically filling vesicles in the basalt.

Heating of hydrated (carnallitic) salt layers, adjacent to a dyke or sill, tends to drive off the water of crystallisation (chemical or hydration thixotropy) at much lower temperatures than that at which anhydrous salts, such as halite or anhydrite, thermally melt (Figure 24c; Table 3). For example, in the Fulda region, the thermally-driven release of water of crystallisation within carnallitic beds creates thixotropic or subsurface “peperite” textures as carnallitite alters to sylvinite layers. These are layers where heated water of crystallisation escaped from the hydrated-salt lattice. Dehydration-driven loss of mechanical strength focuses zones of magma entry into particular subhorizontal horizons in the salt mass, wherever hydrated salt layers were present. In contrast, dyke and sill margins are much sharper and narrower in zones of contact with anhydrous salt intervals and the intrusive is sub-vertical to steeply dipping (Figure 24b versus 24c).

Accordingly, away from the immediate vicinity of the direct thermal aureole, heated and overpressured dehydration waters can enter carnallite halite bed, and drive the creation of extensive soft sediment deformation and peperite textures in hydrated layer (Figure 24c). Mineralogically, sylvite and coarse recrystallised halite dominate the salt fraction in the peperite intervals of the Herfa-Neurode mine. Sylvite in the altered zone is a form of dehydrated carnallite, not a primary-textured salt. Across the Fulda region, such altered zones and deformed units can extend along former carnallite layer to tens or even a hundred or more metres from the dyke feeder. Ultimately, the deformed potash bed passes back out into the unaltered bed, which retains abundant inclusion-rich halite and carnallite (Schofield et al., 2014).

That is, nearer the basalt dyke, the carnallite is largely transformed into inclusion-poor halite and sylvite, the result of incongruent flushing of warm saline fluids mobilised from the hydrated carnallite crystal lattice as it was heated by dyke emplacement. During Miocene salt alteration/thermal metamorphism in the Fulda region, NaCl-fluids were mixed with fluids and gases originating from thermally-mobilised crystallisation water in the carnallite, as it converted to sylvite. This brine/gas mixture altered the basalts during post-intrusive cooling, an event which numerical models suggest was quite rapid (Knipping, 1989): a dyke of less than 0.5 m thickness probably cooled to temperatures less than 200°C within 14 days of dyke emplacement.

The contrast in alteration extent between anhydrous and hydrous salt layers shows alteration effects are minimal wherever the emplacement temperature of the magma is below that of the anhydrous salt body as it is next to a basalt dyke. If this is the mechanism driving entry of igneous-related volatiles (gases and liquids) into a salt body, then the distribution of products (including CO2) will be highly inhomogeneous and related to the minerally of the salt unit adjacent to the intrusive. Worldwide, dykes intersecting salt beds tend to widen to become sills in two zones: 1) along evaporite units within the halite mass that contain hydrated salts, such as carnallite or gypsum (Figure 24c) and, 2) where rising magma has ponded and so created laccoliths at the upper or lower halite contact with the adjacent nonsalt strata or against a salt wall (Figure 22 vs 24). The first is a response to a pulse of released water as dyke-driven heating forces the dehydration of hydrated salt layers. The second is a response to the mechanical strength contrast at the salt-nonsalt contact.

In summary, sylvite formed from a carnallite precursor during Miocene salt alteration/thermal metamorphism in the Fulda region, NaCl-fluids were mixed with fluids originating from thermally-mobilised crystallisation water in the carnallite, as it converted to sylvite. This brine mixture altered the basalts during post-intrusive cooling, an event which numerical models suggest was quite rapid (Knipping, 1989): a dyke of less than 0.5 m thickness probably cooled to temperatures less than 200°C within 14 days of dyke emplacement.

How do we produce potash salts?


Over this series of three articles focused on current examples of potash production, we have seen there are two main groups of potash minerals currently utilised to make fertiliser, namely, muriate of potash (MOP) and sulphate of potash (SOP). MOP is both mined (generally from a Pre-Neogene sylvinite ore) or produced from brine pans (usually via processing of a carnallitite slurry). In contrast, large volumes of SOP are today produced from brine pans in China and the USA but with only minor production for solid-state ore targets. Historically, SOP was produced from solid-state ores in Sicily, the Ukraine, and Germany but today there are no conventional mines with SOP as the prime output in commercial operation (See Salty Matters, May 12, 2015).

The MgSO4-enriched chemistry of modern seawater makes the economic production of potash bitterns from a seawater-feed highly challenging. Today, there is no marine-fed plant anywhere in the world producing primary sylvite precipitates. However, sylvite is precipitating from a continental brine feed in salt pans on the Bonneville salt flat, Utah. There, a brine field, drawing shallow pore waters from saltflat sediments, supplies suitably low-MgSO4 inflow chemistry to the concentrator pans. Sylvite also precipitates in solar evaporator pans in Utah that are fed brine circulated through the abandoned workings of the Cane Creek potash mine (Table 1).

Large-scale production of MOP fertiliser from potash precipitates created in solar evaporation pans is taking place in perennially subaqueous saline pans of the southern Dead Sea and the Qaidam Basin. In the Dead Sea, the feed brine is pumped from the waters of the northern Dead Sea basin, while in the Qaidam sump the feed is from a brine field drawing pore brines with an appropriate mix of river and basinal brine inputs. In both cases, the resulting feed brine to the final concentrators is relatively depleted in magnesium and sulphate. These source bitterns have ionic proportions not unlike seawater in times of ancient MgSO4-depleted oceans. Carnallitite slurries, not sylvinite, are the MOP precipitates in pans in both regions. When feed chemistry of the slurry is low in halite, then the process to recover sylvite is a cold crystallisation technique. When halite impurity levels in the slurry are higher, sylvite is manufactures using a more energy intensive, and hence more expensive, hot crystallisation technique. Similar sulphate-depleted brine chemistry is used in Salar Atacama, where MOP and SOP are recovered as byproducts of the production of lithium carbonate brines.

Significant volumes of SOP are recovered from a combination of evaporation and cryogenic modification of sulfate-enriched continental brines in pans on the edge of the Great Salt Lake, Utah, and Lop Nur, China. When concentrated and processed, SOP is recovered from the processing of a complex series of Mg-K-SO4 double salts (schoenitic) in the Odgden pans fed brines from the Great Salt Lake. The Lop Nur plant draws and concentrates pore waters from a brine field drawing waters from glauberite-polyhalite-entraining saline lake sediments.

All the Quaternary saline lake factories supply less than 20% of the world's potash; the majority comes from the conventional mining of sylvinite ores. The world's largest reserves are held in Devonian evaporites of the Prairie Evaporite in the Western Canada Sedimentary Basin. Textures and mineral chemistry show that the greater volume of bedded potash salts in this region is not a primary sylvite precipitate. Rather the ore distribution, although stratiform and defined by a series of clay marker beds, actually preserves the effects of multiple modifications and alterations tied to periodic egress and ingress of basinal waters. Driving mechanisms for episodes of fluid crossflow range from syndepositional leaching and reflux through to tectonic pumping and uplift (telogenesis). Ore distribution and texturing reflect local-scale (10-100 metres) discontinuities and anomalies created by this evolving fluid chemistry. Some alteration episodes are relatively benign in terms of mineralogical modification and bed continuity. Others, generally tied to younger incidents (post early Cretaceous) of undersaturated crossflow and karstification, can have substantial effects on ore continuity and susceptibility to unwanted fluid entry. In contrast, ore textures and bed continuity in the smaller-scale sylvinite ores in the Oligocene Mulhouse Basin, France, indicate a primary ore genesis.

What makes it economic?

Across the Quaternary, we need a saline lake brine systems with the appropriate brine proportions, volumes and climate to precipitate the right association of processable potash salts. So far, the price of potash, either MOP or SOP, and the co-associated MgSO4 bitterns, precludes industrial marine-fed brine factories.

In contrast, to the markedly nonmarine locations of potash recovery from the Quaternary sources, almost all pre-Quaternary potash operations extract product from marine-fed basinwide ore hosts during times of MgSO4-depleted and MgSO4-enriched oceans (Warren, 2016; Chapter 11). This time-based dichotomy in potash ore sources with nonmarine hosts in the Quaternary deposits and marine evaporite hosted ore zones in Miocene deposits and older, reflects a simple lack of basinwide marine deposits and appropriate marine chemistry across the Neogene (Warren, 2010). As for all ancient marine evaporites, the depositional system that deposited ancient marine-fed potash deposits was one to two orders of magnitude larger and the resultant deposits were typically thicker stacks than any Quaternary potash settings. The last such “saline giant” potash system was the Solfifera series in the Sicilian basin, deposited as part of the Mediterranean “salinity crisis,” but these potential ore beds are of the less economically attractive MgSO4- enriched marine potash series.

So, what are the factors that favour the formation of, and hence exploration for, additional deposits of exploitable ancient potash? First, large MOP solid-state ore sources are all basinwide, not lacustrine deposits. Within the basinwide association, it seems that intracratonic basins host significantly larger reserves of ore, compared to systems that formed in the more tectonically-active plate-edge rift and suture association. This is a reflection of: 1) accessibility – near the shallow current edge of a salt basin, 2) a lack of a halokinetic overprint and, 3) the setup of longterm, stable, edge-dissolution brine hydrologies that typify many intracratonic basins. Known reserves of potash in the Devonian Prairie evaporite in West Canadian Sedimentary Basin (WCSB) are of the order of 50 times that of next largest known deposit, the Permian of the Upper Kama basin, and more than two orders of magnitude larger than any other of the other known exploited deposits (Table 1).

Part of this difference in the volume of recoverable reserves lies in the fact that the various Canadian potash members in the WCSB are still bedded and flat-lying. Beds have not been broken up or steepened, by any subsequent halokinesis. The only set of processes overprinting and remobilising the various potash salts in the WCSB are related to multiple styles and timings of aquifer encroachment on the potash units, and this probably took place at various times since the potash was first deposited, driven mainly by a combination of hinterland uplift and subrosion. In contrast, most of the other significant potash basins listed in Table 10 have been subjected to ongoing combinations of halokinesis and groundwater encroachments, making these beds much less laterally predictable. In their formative stages, the WCSB potash beds were located a substantial distance from the orogenic belt that drove flexural downwarp and creation of the subsealevel sag depression. Like many other intracratonic basins, the WCSB did not experience significant syndepositional compression or rift-related loading.


Adamo, S., 1992, The Sicilian rock salt and potash mines: Mining Magazine, v. 166, p. 277-283.

Adams, S. S., 1970, Ore controls, Carlsbad potash district, southeast New Mexico, in J. L. Rau, and L. F. Dellwig, eds., Third Symposium on Salt, v. 1: Cleveland, Ohio, Northern Ohio Geological Society, p. 246-257.

Baadsgaard, H., 1987, Rb-Sr and K-Ca isotope systematics in minerals from potassium horizons in the Prairie Evaporite Formation, Saskatchewan, Canada: Chemical Geology, v. 66, p. 1-15.

Baar, C. A., 1974, Geological problems in Saskatchewan potash mining due to peculiar conditions during deposition of Potash Beds, in A. H. Coogan, ed., Fourth Symposium on Salt, v. 1: Cleveland, Ohio, North Ohio Geological Society, p. 101-118.

Bastow, I. D., A. D. Booth, G. Corti, D. Keir, C. Magee, C. A.-L. Jackson, J. Warren, J. Wilkinson, and M. Lascialfari, 2018, The development of late-stage continental breakup: Seismic reflection and borehole evidence from the Danakil Depression, Ethiopia: Tectonics, v. 37.

Bingham, C. P., 1980, Solar production of potash from brines of the Bonneville Salt Flats, in J. W. Gwynn, ed., Great Salt Lake; a scientific, history and economic overview. , v. 116, Bulletin Utah Geological and Mineral Survey, p. 229-242.

Blanc-Valleron, M.-M., and M. Schuler, 1997, The Salt Basins of Alsace (Southern Rhine Graben), in G. Busson, and B. C. Schreiber, eds., Sedimentary Deposition in Rift and Foreland Basins in France and Spain (Paleogene and Lower Neogene): New York, Columbia University Press, p. 95–135.

Blanc-Valleron, M. M., 1991, Les formations paléogènes évaporitiques du bassin potassique de Mulhouse et des bassins plus septentrion aux d'Alsace (Document BRGM, 204), Université Louis Pasteur, Paris, 350 p.

Borchert, H., and R. O. Muir, 1964, Salt deposits-The origin, metamorphism and deformation of evaporites: London, D. Van Nostrand Co., Ltd., 338 p.

Boys, C., 1990, The geology of potash deposits at PCS Cory Mine, Saskatchewan: Master's thesis, University of Saskatchewan; Saskatoon, SK; Canada, 225 p.

Boys, C., 1993, A geological approach to potash mining problems in Saskatchewan, Canada: Exploration & Mining Geology, v. 2, p. 129-138.

Braitsch, O., 1971, Salt Deposits: Their Origin and Compositions: New York, Springer-Verlag, 297 p.

Brodylo, L. A., and R. J. Spencer, 1987, Depositional environment of the Middle Devonian Telegraph Salts, Alberta, Canada: Bulletin Canadian Petroleum Geology, v. 35, p. 186-196.

Cendon, D. I., C. Ayora, J. J. Pueyo, and C. Taberner, 2003, The geochemical evolution of the Catalan potash subbasin, South Pyrenean foreland basin (Spain): Chemical Geology, v. 200, p. 339-357.

Cendon, D. I., C. Ayora, J. J. Pueyo, C. Taberner, and M. M. Blanc-Valleron, 2008, The chemical and hydrological evolution of the Mulhouse potash basin (France): Are "marine" ancient evaporites always representative of synchronous seawater chemistry?: Chemical Geology, v. 252, p. 109-124.

Cendon, D. I., C. Ayora, and J. P. Pueyo, 1998, The origin of barren bodies in the Subiza potash deposit, Navarra, Spain - Implications for sylvite formation: Journal of Sedimentary Research Section A-Sedimentary Petrology & Processes, v. 68, p. 43-52.

Cheng, H. D., Q. Y. Hai, H. Z. Ma, X. Y. Zhang, Q. L. Tang, Q. S. Fan, Y. S. Li, and W. L. Miao, 2016, Implications for the origin of secondary sylvite from a simulation of carnallite dissolution: Journal of Geochemical Exploration, v. 165, p. 189-198.

Cheng, H. D., H. Z. Ma, Q. Y. Hai, Z. H. Zhang, L. M. Xu, and G. F. Ran, 2015, Model for the decomposition of carnallite in aqueous solution: Int. J. Miner. Process., v. 139, p. 36-42.

Chipley, D., and T. K. Kyser, 1991, Large scale fluid movement in the Western Canadian sedimentary basin as recorded by fluid inclusions in evaporites, in J. E. Christopher, and F. M. Haidl, eds., Sixth international Williston Basin symposium, v. 6, Special Publication Saskatchewan Geological Society, p. 265-269.

Chipley, D., T. K. Kyser, and T. Danyluk, 1990, Fluid flow events in the Elk Point Baain of western Canada as recorded in evaporite minerals: Summary of Investigations 1990, Saskatchewan Geological Survey; Saskatchewan Energy and Mines, Miscellaneous Report, p. 211-217.

Chipley, D. B. L., 1995, Fluid history of the Saskatchewan sub-basin of the western Canada sedimentary basin: Evidence from the geochemistry of evaporites: Doctoral thesis, University of Saskatchewan.

Chipley, D. B. L., and T. K. Kyser, 1989, Fluid inclusion evidence for the deposition and diagenesis of the Patience Lake Member of the Devonian Prairie Evaporite Formation, Saskatchewan, Canada: Sedimentary Geology, v. 64, p. 287-295.

de Ruiter, P. A. C., 1979, The Gabon and Congo basins salt deposits: Economic Geology, v. 74, p. 419-431.

Dong, Z., P. Lv, G. Qian, X. Xia, Y. Zhao, and G. Mu, 2012, Research progress in China's Lop Nur: Earth-Science Reviews, v. 111, p. 142-153.

Duan, Z. H., and W. X. Hu, 2001, The accumulation of potash in a continental basin: the example of the Qarhan Saline Lake, Qaidam Basin, West China: European Journal of Mineralogy, v. 13, p. 1223-1233.

Eatock, W. H., 1987, The Big Quill Lake sulphate of potash project, in C. F. Gilboy, and L. W. Vigrass, eds., Economic Minerals of Saskatchewan, Proceedings of a Symposium Held in Regina, Saskatchewan 17 & 18 November 1986, : Saskatchewan Geological Society Special Publication Number 8, p. 206–210.

El Tabakh, M., C. Utha-Aroon, and B. C. Schreiber, 1999, Sedimentology of the Cretaceous Maha Sarakham evaporites in the Khorat Plateau of northeastern Thailand: Sedimentary Geology, v. 123, p. 31-62.

Emons, H., and H. Voigt, 1981, Untersvchungen zur kalten zersetzunung von Carnallit.: Freiberg Forschungsher, v. A628, p. 69-78.

Evans, R., 1970, Genesis of sylvite- and carnallite-bearing rocks from Wallace, Nova Scotia: Third Symposium on Salt, v. 1, p. 239-245.


Fabricius, J., and Rose-Hansen, J., 1988, Pressure-dependent melting curve of natural carnallite, KMgCl3.6H2O, in a closed system where evaporation is prevented. IX Symposium on Fluid Inclusions, 4-6 May, 1987, Oporto, Portugal.


Fuzesy, A., 1982, Potash in Saskatchewan: Report, Saskatchewan Department of Mineral Resources, v. 181, 45 p.

Garrett, D. E., 1995, Potash: Deposits, processing, properties and uses: Berlin, Springer, 752 p.

Garrett, D. E., 2004, Handbook of Lithium and natural Calcium Chloride; Their deposits, processing, uses and properties Amsterdam, Elsevier Academic Press, 476 p.

Gendzwill, D. J., 1978, Winnipegosis mounds and Prairie Evaporite Formation of Saskatchewan – seismic study: Bulletin American Association Petroleum Geologists, v. 62, p. 73-86.

Grishina, S., J. Dubessy, A. Kontorovich, and J. Pironon, 1992, Inclusions in salt beds resulting from thermal metamorphism by dolerite sills (eastern Siberia, Russia): European Journal of Mineralogy, v. 4, p. 1187-1202.

Grishina, S., J. Pironon, M. Mazurov, S. Goryainov, A. Pustilnikov, G. Fonderflaas, and A. Guerci, 1998, Organic inclusions in salt - Part 3 - Oil and gas inclusions in Cambrian evaporite deposits from east Siberia - A contribution to the understanding of nitrogen generation in evaporite: Organic Geochemistry, v. 28, p. 297-310.

Gutsche, A., 1988, Mineralreaktionen und Sto€transporte an einem Kontakt Basalt-Hartsalz in der Werra-Folge des Werkes Hattorf: Unpubl. diploma thesis, thesis, Georg-August-Universita, Gottingen.

Hardie, L. A., 1984, Evaporites: Marine or non-marine?: American Journal of Science, v. 284, p. 193-240.

Hardie, L. A., 1990, The roles of rifting and hydrothermal CaCl2 brines in the origin of potash evaporites: an hypothesis: American Journal of Science, v. 290, p. 43-106.

Hinsken, S., K. Ustaszewski, and A. Wetze, 2007, Graben width controlling syn-rift sedimentation: the Palaeogene southern Upper Rhine Graben as an example: International Journal of Earth Sciences, v. 96, p. 979-1002.

Hite, R. J., 1961, Potash-bearing evaporite cycles in the salt anticlines of the Paradox Basin, Colorado and Utah; Article 337: U. S. Geological Survey Professional Paper. p. D323-D327.

Hite, R. J., and T. Japakasetr, 1979, Potash deposits of the Khorat Plateau, Thailand and Laos: Economic Geology, v. 74, p. 448-458.

Hofmann, P., A. Y. Huc, B. Carpentier, P. Schaeffer, P. Albrecht, B. Keely, J. R. Maxwell, D. J. S. Sinninghe, L. J. W. de, and D. Leythaeuser, 1993a, Organic matter of the Mulhouse Basin, France; a synthesis: Organic Geochemistry, v. 20, p. 1105-1123.

Hofmann, P., D. Leythaeuser, and B. Carpentier, 1993b, Palaeoclimate controlled accumulation of organic matter in Oligocene evaporite sediments of the Mulhouse Basin: Organic Geochemistry, v. 20, p. 1125-1138.

Holser, W. T., 1979, Trace elements and isotopes in evaporites in R. G. Burns, ed., Marine Minerals, v. 6, Reviews in Mineralogy, p. 295-346.

Holt, N. M., J. García-Veigas, T. K. Lowenstein, P. S. Giles, and S. Williams-Stroud, 2014, The major-ion composition of Carboniferous seawater: Geochimica et Cosmochimica Acta, v. 134, p. 317-334.

Holter, M., 1972, Geology of the Prairie Evaporite Formation of Saskatchewan, Canada, Geology of saline deposits (Geologie des depots salins), v. 7, UNESCO Earth Sci. Ser., p. 183-189.

Holwerda, J. G., and R. W. Hutchinson, 1968, Potash-bearing evaporites in the Danakil area, Ethiopia: Economic Geology, v. 63, p. 124-150.

Hong, X. L., S. P. Xia, and S. Y. Gao, 1994, Dissolution kinetics of carnallite (in Chinese with English abstract). Chin. J. Appl. Chem., v. 11, p. 26-31.

Horita, J., A. Weinberg, N. Das, and H. Holland, 1996, Brine inclusions in halite and the origin of the Middle Devonian Prairie evaporites of western Canada: Journal of Sedimentary Research Section A-Sedimentary Petrology & Processes, v. 66, p. 956-954.

Hryniv, S. P., B. V. Dolishniy, O. V. Khmelevska, A. V. Poberezhskyy, and S. V. Vovnyuk, 2007, Evaporites of Ukraine: a review: Geological Society, London, Special Publications, v. 285, p. 309-334.

Jensen, G. K. S., B. J. Rostron, M. J. M. Duke, and C. Holmden, 2006, Bromine and stable isotopic profiles of formation waters from potash mine-shafts, Saskatchewan, Canada: Journal of Geochemical Exploration, v. 89, p. 170-173.

Knipping, B., 1989, Basalt intrusions in evaporites: Lecture Notes in Earth Sciences (Springer-Verlag), v. 24, p. 132 pp.

Koehler, G., T. K. Kyser, R. Enkin, and E. Irving, 1997, Paleomagnetic and isotopic evidence for the diagenesis and alteration of evaporites in the Paleozoic Elk Point Basin, Saskatchewan, Canada: Canadian Journal of Earth Sciences, v. 34, p. 1619-1629.

Koehler, G. D., 1997, The Geochemistry and Petrogenesis of Carnallite and its Relationship to the Diagenesis of the Devonian Prairie Formation: PhD thesis, University of Saskatchewan.

Koehler, G. D., T. K. Kyser, and T. Danyluk, 1990, Stable Isotope evidence for the petrogenesis of carnallite In the Middle Devonian Prairie Evaporile Formation, Saskatchewan: Summary of Investigations 1990, Saskatchewan Geological Survey; Saskatchewan Energy and Mines, Miscellaneous Report 90-04.

Liu, C., Y. Ji, Y. Bai, F. Cheng, and X. Lu, 2007, Formation of porous crystals by coupling of dissolution and nucleation process in fractional crystallization: Fluid Phase Equilib, v. 261, p. 300-305.

Lowenstein, T., B. Kendall, and A. D. Anbar, 2014, Chapter 8.21. The Geologic History of Seawater, Treatise on Geochemistry (2nd Edition), Elsevier, p. 569-621.

Lowenstein, T. K., 1988, Origin of depositional cycles in a Permian ''saline giant''; the Salado (McNutt Zone) evaporites of New Mexico and Texas: Geological Society of America Bulletin, v. 100, p. 592-608.

Lowenstein, T. K., and R. J. Spencer, 1990, Syndepositional origin of potash evaporites; petrographic and fluid inclusion evidence: American Journal of Science, v. 290, p. 43-106.

Ma, L., T. K. Lowenstein, B. Li, P. Jiang, C. Liu, J. Zhong, J. Sheng, H. Qiu, and H. Wu, 2010, Hydrochemical characteristics and brine evolution paths of Lop Nor Basin, Xinjiang Province, Western China: Applied Geochemistry, v. 25, p. 1770-1782.

Mackintosh, A. D., and G. A. McVittie, 1983, Geological anomalies observed at the Cominco Ltd. Saskatchewan potash mine: Potash '83; Potash technology; mining, processing, maintenance, transportation, occupational health and safety, environment., p. 59-64.

Matthews, R. D., and G. C. Egleson, 1974, Origin and Implications of a Mid-Basin Potash Facies in the Salina Salt of Michigan, Fourth International Symposium on Salt, v. 1, Northern Ohio Geological Society, p. 15-34.

McIntosh, R. A., and N. C. Wardlaw, 1968, Barren halite bodies in the sylvinite mining zone at Esterhazy, Saskatchewan: Canadian Journal of Earth Sciences, v. 5, p. 1221-1238.

Mossman, D. J., R. N. Delabio, and A. D. Mackintosh, 1982, Mineralogy of clay marker seams in some Saskatchewan potash mines: Canadian Journal of Earth Sciences, v. 19, p. 2126-2140.

Mossop, G., and I. Shetsen, 1994, Geological Atlas of the Western Canada Sedimentary Basin: Canadian Society of Petroleum Geologists and Alberta Research Council, 504 p.

Prud'homme, M., and S. T. Krukowski, 2006, Potash, in J. E. Kogel, N. C. Trivedi, J. M. Barker, and S. T. Krukowski, eds., Industrial Minerals and Rocks, SME (Soc. Mining Metallurgy and Exploration), p. 723-742.

Richter-Bernburg, G., 1986, Zechstein 1 and 2 anhydrites; facts and problems of sedimentation, in G. M. Harwood, and D. B. Smith, eds., The English Zechstein and related topics, v. 22: London, UK, Geological Society Special Publication, p. 157-163.

Rogers, M. B., and B. Pratt, 2017, Stratigraphy of the Middle Devonian Keg River and Prairie Evaporite formations, northeast Alberta, Canada: Bulletin of Canadian Petroleum Geology, v. 65, p. 5-63.

Root, K. G., 2001, Devonian Antler Fold and Thrust Belt and Foreland Basin Development in the Southern Canadian Cordillera: Implications for the Western Canada Sedimentary Basin: Bulletin of Canadian Petroleum Geology, v. 49, p. 7-36.

Rosell, L., and F. Ortí, 1981, The saline (potash) formation of the Navarra basin (Upper Eocene, Spain). Petrology: Revista Instituto Investigaciones Geologicas, v. 35, p. 71-121.

Rouchy, J.-M., 1997, Paleogene Continental Rift System of Western Europe: locations of basins, paleogeographic and structural framework, and the distribution of evaporites: In: Busson, G., Schreiber, B.C. (Eds.), Sedimentary Deposition in Rift and Foreland Basins in France and Spain (Paleogene and Lower Neogene). Columbia University Press, New York, pp. 45–94.

Schofield, N., I. Alsop, J. Warren, J. R. Underhill, R. Lehné, W. Beer, and V. Lukas, 2014, Mobilizing salt: Magma-salt interactions: Geology, v. 42, p. 599-602.

Schwerdtner, W. M., 1964, Genesis of potash rocks in Middle Devonian Prairie Evaporite Formation of Saskatchewan: Bulletin American Association Petroleum Geologists, v. 48, p. 1108-1115.

Schwerdtner, W. M., 1964, Genesis of potash rocks in Middle Devonian Prairie Evaporite Formation of Saskatchewan: Bulletin American Association Petroleum Geologists, v. 48, p. 1108-1115.

Smith, D. B., 1996, Deformation in the late Permian Boulby Halite (EZ3Na) in Teesside, NE England: Geological Society, London, Special Publications, v. 100, p. 77-87.

Smith, D. B., and A. Crosby, 1979, The regional and stratigraphical context of Zechstein 3 and 4 potash deposits in the British sector of the southern North Sea and adjoining land areas: Economic Geology, v. 74, p. 397-408.

Steinmann, M., P. Stille, W. Bernotat, and B. Knipping, 1999, The corrosion of basaltic dykes in evaporites: Ar-Sr-Nd isotope and rare earth elements evidence: Chemical Geology, v. 153, p. 259-279.

Szatmari, P., R. S. Carvalho, and I. A. Simoes, 1979, A comparison of evaporite facies in the late Paleozoic Amazon and the Middle Cretaceous South Atlantic salt basins: Economic Geology, v. 74, p. 432-447.

Valyashko, M. G., 1972, Playa lakes, a necessary stage in the development of a salt-bearing basin [with discussion]: Geology of saline deposits, Unesco Earth Sci. Ser., p. 41-51.

van't Hoff, J. H., 1912, Untersuchungen Uber die Bildungsurhältnisse der ozeanischen Salzablangerungen, insbesondere das Stassfurter Salzlagers: Leipzig.

Voigt, W., 2015, What we know and still not know about oceanic salts: Pure Appl. Chem., v. 87, p. 1099-1026.

Volozh, Y., C. J. Talbot, and A. Ismail-Zadeh, 2003, Salt structures and hydrocarbons in the Pricaspian basin: Bulletin American Association Petroleum Geologists, v. 87, p. 313-334.

Wall, M., J. Cartwright, R. Davies, and A. McGrandle, 2010, 3D seismic imaging of a Tertiary Dyke Swarm in the Southern North Sea, UK: Basin Research, v. 22, p. 181-194.

Wardlaw, N. C., 1968, Carnallite-sylvite relationships in the middle Devonian Prairie evaporite formation, Saskatchewan: Geological Society America Bulletin, v. 79, p. 1273-1294.

Wardlaw, N. C., 1972a, Unusual marine evaporites with salts of calcium and magnesium chloride in Cretaceous basins of Sergipe, Brazil: Economic Geology, v. 67, p. 156-168.

Wardlaw, N. C., 1972b, Syn-sedimentary folds and associated structures in Cretaceous salt deposits of Sergipe, Brazil: J. Sediment. Petrol., v. 42, p. 572-577.

Wardlaw, N. C., and G. D. Nicholls, 1972, Cretaceous Evaporites of Brazil and West Africa and their Bearing on the Theory of Continent Separation.: 24th Inter. Geol. Congr., v. 6, p. 43-55.

Wardlaw, N. C., and D. W. Watson, 1966, Middle Devonian salt formations and their bromide content, Elk Point area, Alberta: Canadian Journal of Earth Sciences, v. 3, p. 263-275.

Warren, J. K., 2000, Geological controls on the quality of potash, in R. M. Geertmann, ed., 8th World Salt Symposium, v. 1: Amsterdam, Elsevier, p. 173-180.

Warren, J. K., 2010, Evaporites through time: Tectonic, climatic and eustatic controls in marine and nonmarine deposits: Earth-Science Reviews, v. 98, p. 217-268.

Warren, J. K., 2011, Evaporitic source rocks: mesohaline responses to cycles of “famine or feast” in layered brines, Doug Shearman Memorial Volume, (Wiley-Blackwell) IAS Special Publication Number 43, p. 315-392.

Warren, J. K., 2016, Evaporites: A compendium (ISBN 978-3-319-13511-3): Berlin, Springer, 1854 p.

Warren, J. K., 2017, Salt usually seals, but sometimes leaks: Implications for mine and cavern stabilities in the short and long term: Earth-Science Reviews, v. 165, p. 302-341.

Williams-Stroud, S. C., 1994, Solution to the Paradox? Results of some chemical equilibrium and mass balance calculations applied to the Paradox Basin evaporite deposit: American Journal of Science, v. 294, p. 1189-1228.

Wittrup, M. B., and T. K. Kyser, 1990, The petrogenesis of brines in Devonian potash deposits of western Canada: Chemical Geology, v. 82, p. 103-128.

Woods, P. J. E., 1979, The geology of Boulby Mine: Economic Geology, v. 74, p. 409-418.

Worsley, N., and A. Fuzesy, 1979, The potash-bearing members of the Devonian Prairie Evaporite of southeastern Saskatchewan, south of the mining area: Economic Geology, v. 74, p. 377-388.

Xia, S. P., X. L. Hong, and S. Y. Gao, 1993, Study on the dissolution kinetics and mechanism of carnallite and KC (in Chinese with English abstract): Journal Salt Lake Research, v. 1, p. 52-60.

Yang, C., G. Jensen, and J. Berenyi, 2009, The Stratigraphic Framework of the Potash-rich Members of the Middle Devonian Upper Prairie Evaporite Formation, Saskatchewan: Summary of Investigations 2009, Saskatchewan Geological Survey; Misc. Rep. 2009-4.1, 28 p.

Zak, I., 1997, Evolution of the Dead Sea brines, in T. M. Niemi, Z. Ben-Avraham, and J. R. Gat, eds., The Dead Sea, The Lake and Its Setting, v. 36: Oxford, Oxford University Press; Monographs on Geology and Geophysics, p. 133-144.

Zharkov, M. A., 1984, Paleozoic salt bearing formations of the world: Berlin, Springer Verlag, 427 p.


Evaporites and climate: Part 2 of 2 - Ancient evaporites

John Warren - Saturday, February 25, 2017


Evaporites, along with coal and bauxites, are sediments considered to be climate sensitive. Ancient evaporite distribution and associated paleolatitudes are used to reconstruct the distribution of the world's arid belts across time. As we saw in Part 1 (Salty Matters, Tuesday, January 31, 2017), thick, widespread evaporite deposit are essentially a result of the atmospheric circulation of the Hadley cells. That is, locations of subtropical dry zones and tropical/subtropical deserts of the globe are mostly determined by the positions of subsiding branches of cool, dry descending air in a Hadley cells (aka Trade Wind Belt; Lu et al., 2007; Crowley and North, 1991) within low-lying regions tied a sufficient supply of mother brine. Thus, climate plus ongoing brine supply are the underlying factors controlling locales of significant evaporite deposition (Ziegler et al., 1981). The previous article focused on regional and local climatic controls across the Quaternary (Salty Matters, Tuesday, January 31, 2017). This article extends the time frame for the evaporite/climate association across the Phanerozoic and into the Precambrian.

As we move back in time, we move out of an icehouse-dominated world climate, with permanent ice caps waxing and waning at the world's poles, into greenhouse-dominant world climates. In greenhouse times there are no permanent polar ice sheet and glaciers occurred only in some high-altitude mountainous belts (Figure 1a, b). The transition into greenhouse climate changes the dominant 4th-order eustatic style from 100m amplitude changes every 100,000 years or so into 4th-order responses with much lower 3-5 m amplitude oscillations every 100,000 years (Figure 2a, b). Lack of polar caps raises world sealevel on the order of 40-50 metres. Thus, even without tectonic considerations, there is less continental freeboard in greenhouse times and increased the potential for significant cratonic coverage by epicontinental and pericontinental seaways (Warren, 2016; Chapter 5).

Looking back in time, beyond the last few million years of the Quaternary, means our conceptual models must encompass a broader range of tectonic settings as well as changes in the rates of seafloor spreading, supercontinents, and times of significant igneous outpourings (superplumes). All these additional world-scale variables across a longer set of available time explain the greater range of climate potentials on the earth, compared to anything that has occurred in the time-limited base seen in icehouse-dominant Quaternary climate spreads. The last few million years of the current icehouse mode is inhabited by the human species or its primate ancestors. The previous Icehouse dominant mode was in the Carboniferous-Mid Permian when the dominant land animals were amphibians and primitive reptiles.
One the first questions this broader ancient climate spectrum, tied to evaporites over deep time, offers up is; "How do the positions of Hadley cells vary across geological time frames?" In part 1, we saw how the rise of the Himalayas deflected a belt of cool, dry descending air much further south toward the Equator. Moving back in time creates a broader scaffolding for documenting climate variation, in part driven by the rise and fall of mountain ranges, but also influenced by increases in the rate of seafloor spreading driving ocean basin shallowing and by changes in atmospheric/seawater compositions and temperatures.

Hadley cells and latitudinal variability over time
According to Chen Xu et al., 2013 and Boucot et al., 2013, much of the world-scale Phanerozoic distribution of significant bedded evaporite accumulations indicates the ongoing presence of two mid-latitude arid belts, presumably situated beneath Hadley Cells. There are exceptions in locales generated in local rain shadows with orographic control provided by neighbouring mountain ranges. However, in the later Permian, through the Triassic, and much of the Jurassic the two formerly mid-latitude Hadley Cells merged over the more central Pangaeanic regions of Africa, Europe and the adjacent Americas, to form an arid belt that also encompassed low-latitude, equatorial arid regions (Figure 3). Across the continental interior of the Pangean supercontinent, this arid to hyperarid equatorial belt in the supercontinent interior prevented the formation of climate-sensitive sediments that are more typical of humid equatorial conditions that deposit coals, kaolinites, lateritic materials and bauxites. However, in this same time interval, these more humid sediment products are typically present at low latitudes of these time slices adjacent to the Panthalassic ocean.
That is, in the absence of an equator-spanning supercontinent, low latitudes, typically imply humid and non-seasonal tropical conditions throughout much of the Phanerozoic, as we see today. But the assembly of the Pangaean supercontinent disrupted this latitudinally-zoned atmospheric circulation, replacing it with a progressively more monsoonal (seasonal) circulation and more arid, at times hyperarid, conditions in the equatorial continental interior of Pangaea (Parrish, 1993). The Pangean supercontinent reached its maximum areal extent in the Triassic and was associated with what is known as the Pangaean Megamonsoon. There were immense arid regions across the interior regions of the supercontinent that were nearly uninhabitable, with scorching days and frigid nights. However, Panthalassian coasts still experienced seasonality, transitioning from rainy weather in the summer to dry conditions during the winter and the associated accumulation of humid sediments (Figure 3b' Boucot et al., 2013). Megamonsoon aridity is evidenced not just in the accumulation of low-latitude bedded evaporite deposits. Low latitude continental aridity also drove the accumulation of thick, widespread low-latitude desert redbeds, sourced by eolian, not fluvial, detrital transport (Sweet at al., 2013) and the precipitation of bedded salt crusts in ephemeral saline lakes under exceptionally-high surface temperatures of up to 73°C (Zambito and Benison, 2013).
Paleolatitude reconstructions Chen-Xu et al. (2013) show these continental interior arid belts in low latitude tropical-subtropical regions persisted from the Permian to the Early Cretaceous. Reunion of the humid regions from both sides of Pangaea by the early Late Cretaceous formed a through-going low latitude humid tropical-subtropical belt. This coincides with the disaggregation of Pangaean supercontinent, as the initial stages of a modern latitudinal climate belt distribution pattern emerged, tied to latitudinally-restricted evaporites that continue to the present (Figure 4).

Tectonism and eustacy in arid climates drive the formation of mega-evaporite basins
Within this Phanerozoic climatic framework, there are times when significant volumes of evaporites form what are know as saline giants, or megahalite/megasulphates deposits. These massive accumulations of salts formed beneath arid climates that can span both greenhouse and icehouse climates (Figure 1; Warren, 2010, 2016). Ancient marine saline giants (megahalites and megasulphates) accrued in either of two plate-scale settings, which at times merged into one another, namely; 1) Platform evaporites (Figure 5) and, 2) Basinwide evaporites (Figure 6).

The first major contrast with nonmarine continental dominance in Quaternary evaporite settings is the fact that platform evaporites require greenhouse eustasy a and a marine feed, the second is that basinwide evaporites require tectonically- and hydrographically-isolated widespread subsealevel depressions, typically found along plate edges with continent-continent proximity in regions with a marine seepage feed and/or periodic marine overflows (Figure 6). Neither platform or basinwide conditions are present on the current earth surface. For basinwides, suitable hydrologic conditions were last present during the Messinian Salinity Crisis in the Mediterranean region, and platform evaporite settings were last present on earth across large parts of the Middle East carbonate platform during the Eocene (Tables 1, 2). There is a third group of ancient evaporite deposits; it encompasses all nonmarine lacustrine beds past and present (Table 3). This group has same-scale modern-ancient counterparts, unlike ancient marine platform and basinwide evaporites (Warren, 2010, 2016). Interestingly, the lacustrine depositional style for bedded salt accumulation dominates in the icehouse climate that is the Quaternary, and so biases a strictly uniformitarian view of the past with respect to the relative proportions of nonmarine versus marine evaporite volumes (see Part 1; Salty Matters, Tuesday, January 31, 2017).

Platform evaporites
Are made up of stratiform beds, usually <50 m thick and composed of stacked <1 to 5 m thick parasequences or evaporite cycles, with a variably-present restricted-marine carbonate unit at a cycle base (Table 1). Salts were deposited as mixed evaporitic mudflat and saltern evaporites, sometimes with local accumulations of bittern salts. Typically, platform salts were deposited in laterally extensive (>50-100 km wide), hydrographically-isolated, subsealevel marine-seepage lagoons (salterns) and evaporitic mudflats (sabkhas and salinas). These regions have no same-scale modern counterparts and extended as widespread depositional sheets across large portions of hydrographically isolated marine platform areas that passed seaward across a subaerial seepage barrier into open marine sediments (Figure 5). In marine margin epeiric settings, such as the Jurassic Arab/Hith and Permian Khuff cycles of the Middle East or the Cretaceous Ferry Lake Anhydrite in the Gulf of Mexico, these platform evaporites are intercalated with shoalwater marine-influenced carbonate shelf/ramp sediments, which in turn pass basinward across a subaerial sill into open marine carbonates. Landward they pass into arid zone continental siliciclastics or carbonate mudflats.


Platform evaporite deposition occurred in both pericontinental and epicontinental settings, at times of low-amplitude 4th and 5th order sealevel changes, which typify greenhouse eustasy (Figure 5; Warren, 2010). Platform evaporites also typify the saline stages of some intracratonic basins. Platform evaporites cannot form in the high-amplitude, high-frequency sealevel changes of Icehouse eustasy. The 100m+ amplitude oscillations of Icehouse times mean sealevel falls off the shelf edge every 100,000 years, so any evaporite that had formed on the platform is subaerially exposed and leached. Fourth order high-amplitude icehouse eustatic cycles also tend to prevent laterally-continuous carbonate sediment barriers forming at the top of the shelf to slope break, and so icehouse evaporite systems tend not to be hydro-graphically isolated (drawdown) at the platform scale. Rather icehouse eustasy favours nonmarine evaporites as the dominant style, along with small ephemeral marine-margin salt bodies, as seen today in the bedded Holocene halites and gypsums of Lake Macleod in coastal West Australia (Part 1; Salty Matters, Tuesday, January 31, 2017).
Ancient platform evaporite successions may contain halite beds, especially in intracratonic basinwide settings, but periplatform settings, outside of intracratonic basins, are typically dominated by 5–40 m thick Ca-sulphate beds intercalated with normal-marine platform carbonates (Table 1). The lateral extent of these epeiric platform sulphate bodies, like the Middle Anhydrite Member of the Permian Khuff Fm. of Saudi Arabia and the UAE, with a current area of more than 1,206,700 sq. km., constitute some of the most aerially-extensive evaporite beds ever deposited.

Basinwide evaporites
Are made up of thick evaporite units >50–100 m thick made up of varying combinations of deepwater and shallow water evaporites (Figure 1; Table 2). They retain textural evidence of different but synchronous local depositional settings, including mudflat, saltern, slope and basin (Figure 6). When basinwide evaporite deposition occurs, the whole basin hydrology is evaporitic, holomictic, and typically saturated with the same mineral phase across vast areas of the basin floor, as seen on a much smaller scale today in the Dead Sea basin. The Dead Sea currently has halite forming simultaneously as; 1) decimeter-thick chevron-dominated beds on the saline-pan floor of the shallow parts around the basin edge in waters typically less than 1-10 metres deep, and 2) as coarse inclusion-poor crystal meshworks of halite on the deep basin floor that sits below a halite-saturated brine column up to hundreds of metres deep. Ancient basinwide successions are usually dominated by thick massive salt beds, generally more than 100-500 m thick. Deposits are made up of stacked thick halite beds, but can also contain substantial volumes of thick-bedded Ca-sulphate and evaporitic carbonate, as in the intracratonic basinwide accumulations of the Delaware and Otto Fiord Ba-sins (Table 2).
Owing to inherent purity and thickness of the deposited halite, many halite-dominant basinwide beds are also remobilized, via loading or tectonics, into various halokinetic geometries (Hudec and Jackson, 2007). Some basinwide systems (mostly marine-fed intracratonic settings) entrain significant accumulations of marine-fed potash salts, as in the Devonian Prairie Evaporite of western Canada. In contrast, all Quaternary examples of commercial potash deposits are accumulating in continental lacustrine systems (Warren 2016; Chapter 11).


Basinwide evaporite deposits are the result of a combination of tectonic and hydrological circumstances that are not currently active on the world’s surface (Figure 1). They were last active in the Late Miocene (Messinian), in association with soft-suture collision basins tied to the Alpine-Himalaya orogenic belt, and in Middle Miocene (Badenian) basins developed in the early rift stages of the Red Sea. Basinwide systems will be active again in the future at sites and times of appropriate plate-plate interaction, when two continental plate edges are nearby, and the intervening seafloor is in or near a plate-edge rift or suture and is both subsealevel and hydrographically isolated (Figure 6). Unlike most platform evaporites, basinwides do not require greenhouse eustacy, only the appropriate association of arid climate and tectonics. The latter sets up a deep hydrographically-isolated subsealevel tectonic depression with a geohydrology that can draw on a huge reserve of marine mother brine in the nearby ocean. For this reason, saline giants tend to form at times of plate-scale continent-continent proximity and so occur mostly in craton-margin settings.


Lacustrine (nonmarine) evaporites
Quaternary continental playa/lacustrine are constructed of stratiform salt units, with the greater volume of saline sediment accumulating in lower, more-saline portions of the lacustrine landscape. Beds are usually dominated by nodular gypsum and displacive halite, deposited in extensive evaporitic mudflats and saltpans with textures heavily overprinted by capillary wicking, rather than as bedded bottom-nucleated layers on the subaqueous floors of perennial brine lakes (Ruch et al., 2012). In ancient counterparts, the total saline lacustrine thickness ranged from meters to hundreds of meters, with lateral extents measured in tens to hundreds of kilometres (Table 3). Lacustrine salt beds are separated vertically, and usually surrounded by, deposits of lacustrine muds, alluvial fans, ephemeral streams, sheet floods, eolian sands, and redbeds. As today, ancient lacustrine salts accumulated in endorheic or highly restricted discharge basins, with perennial saline water masses tending to occur in the drainage sumps of steep-sided drainage basins (Warren, 2010, 2016). Saline lake basins accumulating gypsum, or more saline salts like halite or glauberite, typically have a shallow water table in peripheral saline mudflat areas and so are dominated by continental sabkha textures. Nearby is the lowermost part of the lacustrine depression or sump where deposition is typified by ephemeral ponded brine pan deposits, rather than permanent saline waters.
Saline lacustrine mineralogies depend on compositions of inflowing waters, so depositional sumps in regions with non-marine ionic proportions in the feeder inflow, accumulate thick sequences of nonmarine bedded salts dominated by trona, glauberite, and thenardite. In contrast, nonmarine areas with thalassic (seawater-like) inflows tend to accumulate more typical sequences of halite, gypsum, and anhydrite.
Across the Pliocene-Quaternary icehouse, less-saline perennial saline-lake beds tend to occur during more humid climate periods in the same continental-lacustrine depressions where saline-pan beds form (e.g., Lake Magadi, Great Salt Lake, Lake Urmia). On a smaller scale, in some modern saline lake basins, parts of the lake floor can be permanently located below the water surface (Northern Basin in the Dead Sea or Lake Asal). In some modern saline sumps dominated by mudflats, a perennial saline lake water mass is located toward the edge of a more central salt-flat zone, forming a perennial water filled “moat” facies surrounding a seasonally desiccated saline pan (as in Salar, de Atacama, Salar de Uyuni, Lake Magadi, Lake Natron). These permanent to near-permanent saline water “moat” regions are typically created where fresher inflows encounter saltier beds of the lake centre, dissolve them, and so form water-filled peripheral depressions. Bottom sediment in the moats tends to be mesohaline carbonate laminites, which can contain TOC levels as high as 12%.
High-water stage perennial saline lacustrine sediments tend to be carbonate-rich or silica-rich (diatomaceous) laminites. Ancient examples of large saline lacustrine deposits made up of alternating humid and desiccated lacustrine units include the Eocene Green River Formation of Wyoming and the Permian Pingdiquan Formation of the Junggar Basin, China (Table 4). Evaporites deposited in a suprasealevel lacustrine basin (especially Neogene deposits) have numerous same-scale Quaternary analogues, unlike the more voluminous ancient marine platform and basinwide evaporites (Figure 7). Clearly, across the Quaternary, saline continent lacustrine settings possess areas of bedded salt accumulation that are far greater than those of any contemporaneous marine-fed salt sumps (Part 1; Salty Matters, Tuesday, January 31, 2017). But in ancient climes, especially during in the continental interior of the Pangean supercontinent (mid Permian to Triassic), regions of continental interior sabkhas and saline pans had areas far greater than any seen in Quaternary continental saline sumps (Zambia and Benison, 2013).

Is the present-day climate the key to evaporite understanding?
This short answer is yes, Hadley Cells across the Phanerozoic are mostly tied to climate belts that maintain sub-tropical positions, but to this notion, we must add a geological context. Today we are living in an icehouse climate mode and have been for the last 12 Ma. It is tied to the presence of polar ice-sheets that wax and wane over 100,000-year time frames, so moving the position of the Hadley cells and changing the intensity of atmospheric circulation. In this icehouse climate, large eustatically-controlled marine-fed evaporite deposits are not preserved, as sea level falls off the continental shelf every 100,000 years or so. The world's largest bedded salt deposits formed sometime in the last 2 million years, are found in continental interiors, typically in endorheic tectonic sumps in either hot arid or steppe climate settings, often with salt diapirs outcropping or subcropping in the drainage basin and the basin floor can be located at elevations well above sealevel (Part 1; Salty Matters, Tuesday, January 31, 2017).
As we move back into much of Phanerozoic time, we see world climates dominated by greenhouse modes, with shorter episodes of polar ice-sheets and icehouse climates in the Carboniferous-Early Permian ≈ 50 million years long, and the Ordovician, some 15 million years long (Figure 1). Greenhouse climate lacks permanent polar ice sheets, so sea-levels are higher, and 4th-order eustatic amplitudes in sea level are much less (a few meters versus hundred meters plus changes). Greenhouse sets up epeiric and intercontinental seaways that when hydrographically isolated, but still marine-fed, can deposit huge areas of platform evaporites centred in isolated seepage-fed sub-sealevel sumps. These platform deposits can also form outside of Greenhouse times in marine-fed tectonically-induced intracratonic sumps.
Basinwide evaporite deposits span icehouse and greenhouse mode arid belts, whenever a marine-fed subsealevel tectonic sump forms at positions of continent-continental proximity in an arid belt. Across much of the Phanerozoic, basinwide deposits typically accumulated beneath subtropical belts of cool, dry descending air set up in a Hadley cell, and so are located north and south of a tropical equatorial belt. But the accretion of the Pangaean supercontinent (Carboniferous to Jurassic) set up conditions of continentality and orographic shadowing that allowed an arid saline belt to span the hyperarid interior of the supercontinent.

Boucot, A., Chen-Xu, and C. Scotese, 2013, Phanerozoic Paleoclimate: An Atlas of Lithologic Indicators of Climate: Concepts in Sedimentology and Paleontology, v. 11: Tulsa, OK, SEPM, 32 p.

Chen-Xu, A. J. Boucot, C. R. Scotese, F. Junxuan, W. Yuan, and Z. Xiujuan, 2012, Pangaean aggregation and disaggregation with evidence from global climate belts: Journal of Palaeogeography, v. 1, p. 5-13.

Crowley, T. J., and G. R. North, 1991, Paleoclimatology: New York, Oxford University Press, 339 p.

Hudec, M. R., and M. P. A. Jackson, 2007, Terra infirma: Understanding salt tectonics: Earth-Science Reviews, v. 82, p. 1-28.

Lu, J., G. A. Vecchi, and T. Reichler, 2007, Expansion of the Hadley cell under global warming: Geophysical Research Letters, v. 34.

Parrish, J. T., 1993, Climate of the Supercontinent Pangea: Journal of Geology, v. 10.

Ruch, J., J. K. Warren, F. Risacher, T. R. Walter, and R. Lanari, 2012, Salt lake deformation detected from space: Earth and Planetary Science Letters, v. 331-332, p. 120-127.

Sweet, A. C., G. S. Soreghan, D. E. Sweet, M. J. Soreghan, and A. S. Madden, 2013, Permian dust in Oklahoma: Source and origin for Middle Permian (Flowerpot-Blaine) redbeds in Western Tropical Pangaea: Sedimentary Geology, v. 284–285, p. 181-196.

Warren, J. K., 2010, Evaporites through time: Tectonic, climatic and eustatic controls in marine and nonmarine deposits: Earth-Science Reviews, v. 98, p. 217-268.

Warren, J. K., 2016, Evaporites: A compendium (ISBN 978-3-319-13511-3): Berlin, Springer, 1854 p.

Zambito, J. J., and K. C. Benison, 2013, Extremely high temperatures and paleoclimate trends recorded in Permian ephemeral lake halite: Geology, v. 41, p. 587-590.

Ziegler, A. M., S. F. Barrett, C. R. Scotese, and B. W. Sellwood, 1981, Palaeoclimate, Sedimentation and Continental Accretion [and Discussion]: Philosophical Transactions of the Royal Society of London. Series A, Mathematical and Physical Sciences, v. 301, p. 253-264.



Recent Posts


Ethiopia carbon cycle deep seafloor hypersaline anoxic basin oil gusher NaSO4 salts gem salt karst brine lake edge sodium silicate Large Igneous Magmatic Province perchlorate DHAL vadose zone Hadley cell: lot's wife silica solubility vestimentiferan siboglinids Hyperarid evaporite-metal association nacholite sulphur Lomagundi Event evaporite dissolution collapse doline carbon oxygen isotope cross plots supercontinent salt seal solikamsk 2 Ripon jadarite Ceres Sulphate of potash lazurite Koeppen Climate hydrogen halite-hosted cave Ure Terrace gypsum dune methanotrophic symbionts Mars halokinetic Warrawoona Group well log interpretation evaporite karst Deep Lop Nur Dead Sea karst collapse sedimentary copper Magdalen's Road dissolution collapse doline 18O base metal H2S circum-Atlantic Salt Basins Seepiophila jonesi SO2 stable isotope zeolite halite well logs in evaporites Noril'sk Nickel retrograde salt Lamellibrachia luymesi hectorite Salar de Atacama authigenic silica palygorskite MgSO4 depleted anomalous salt zones solar concentrator pans MOP halogenated hydrocarbon hydrological indicator Platform evaporite Lake Magadi Stebnik Potash basinwide evaporite sulfate lunette cauliflower chert Paleoproterozoic Oxygenation Event causes of major extinction events saline clay Mulhouse Basin crocodile skin chert carnallitite McMurdo Sound Proterozoic Dead Sea saltworks Muriate of potash trona Jefferson Island salt mine silicified anhydrite nodules Weeks Island salt mine Dead Sea caves antarcticite HYC Pb-Zn Karabogazgol seal capacity Stebnyk potash sinjarite climate control on salt extraterrestrial salt marine brine sinkhole Atlantis II Deep potash ore price salt trade brine evolution Mega-monsoon Prairie Evaporite lapis lazuli Zaragoza mass die-back Pilbara Corocoro copper saline giant Pangaea chert gas in salt North Pole RHOB Neoproterozoic Oxygenation Event End-Triassic Musley potash Europe blowout 13C Mesoproterozoic endosymbiosis SedEx lithium brine DHAB brine pan Badenian mine stability Crescent potash Thiotrphic symbionts halotolerant mummifiction subsidence basin MgSO4 enriched Clayton Valley playa: alkaline lake Density log lithium battery eolian transport extrasalt bischofite Five Island salt dome trend phreatic explosion Realmonte potash evaporite-hydrocarbon association hydrothermal karst tachyhydrite K2O from Gamma Log CaCl2 brine ancient climate Patience Lake member namakier freefight lake anthropogenic potash mirabilite York (Whitehall) Mine Red Sea capillary zone Lop Nor wireline log interpretation flowing salt MVT deposit natural geohazard Hell Kettle potash ore ozone depletion potash well blowout SOP gassy salt doline GR log Calyptogena ponderosa halocarbon Mixing zone kainitite hydrohalite High Magadi beds Kara bogaz gol Precambrian evaporites evaporite Lake Peigneur Deep seafloor hypersaline anoxic lake epsomite methane causes of glaciation cryogenic salt McArthur River Pb-Zn source rock sulphate Boulby Mine nitrogen nuclear waste storage Enceladus snake-skin chert rockburst Belle Isle salt mine geohazard Kalush Potash phreatomagmatic explosion salt periphery salt tectonics Evaporite-source rock association stevensite Stolz diapir intrasalt LIP salt leakage, dihedral angle, halite, halokinesis, salt flow, Messinian Great Salt Lake venice astrakanite black salt Schoenite Neoproterozoic methanogenesis meta-evaporite recurring slope lines (RSL) Gamma log sulfur sepiolite gas outburst salt mine magadiite Turkmenistan allo-suture NPHI log 18O enrichment Archean Neutron Log auto-suture End-Cretaceous Bathymodiolus childressi salt suture Koppen climate Prograde salt Sumo hydrothermal potash bedded potash Phaneozoic climate Belle Plain Member anthropogenically enhanced salt dissolution halophile seawater evolution Catalayud End-Permian water in modern-day Mars Danakhil Depression, Afar organic matter knistersalz Zabuye Lake Dallol saltpan Ganymede vanished evaporite dihedral angle Quaternary climate water on Mars Ingebright Lake waste storage in salt cavity 13C enrichment African rift valley lakes CO2: albedo intersalt dark salt Hadley Cell cryogenic spring salts deep meteoric potash salt ablation breccia lithium carbonate CO2